Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG
- Product Code
- 2851326
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Pressure Sensitive Adhesives
Uses advised against
None identified
Manufacturers & Suppliers
Henkel
manufacturer
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
IDH number: 2851326
Notes
Hazardous Component(s): None
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. If symptoms develop and persist, get medical attention.
Cool melted product on skin with plenty of water. Do not remove solidified product. No attempt should be made to remove material from skin or to remove contaminated clothing as damaged skin can be easily torn. Cover affected areas with clean sheeting or gauze and seek immediate medical attention.
Symptoms: Molten adhesive may cause severe burns.
If eye contact occurs with molten material immediately cool with water. Do not remove adhesive. Seek medical attention.
If symptoms develop and persist, get medical attention.
Immediate Medical Attention
Seek immediate medical attention for skin burns. Seek medical attention for eye contact or if inhalation/ingestion symptoms develop and persist.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures appropriate to local circumstances and the surrounding environment. Dry chemical. Carbon dioxide.
In case of fire toxic gases can be released.
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Wear full protective clothing.
Firefighter Protection
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Wear full protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not empty into drains / surface water / ground water.
Scrape up spilled material and place in a closed container for disposal.
Related Products
Similar products with comparable safety profiles
LOCTITE DURO-TAK UV VP 4660ELGIN CAN-3KG
---
LOCTITE DURO-TAK UV 4194 ULTRA DR-F181KG
---
LOCTITE DURO-TAK UV 4660 ULTRA PA16KG
---
LOCTITE DURO-TAK UV 4616NA DR-F 181KG
---
LOCTITE DURO-TAK UV 7020 ULTRA PA-16KG
---
LOCTITE DURO-TAK UV VP 5008BP PA 16KG
---
LOCTITE DURO-TAK UV 7020 ULTRA DR-F181KG
---
LOCTITE DURO-TAK UV 7050 ULTRA DR-F181KGKG
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Always be careful around molten material. Follow suggested application temperature. Do not wear contact lenses. At elevated temperatures, irritating fumes may be emitted.
Store in a cool, dry, well-ventilated area.
Do not wear contact lenses.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Work should be done in an adequately ventilated area (i.e., ventilation sufficient to maintain concentrations below one half of the PEL and other relevant standards). Local exhaust ventilation is recommended when general ventilation is not sufficient to control airborne contamination.
Insulated gloves
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists. Do not wear contact lenses.
Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Observe OSHA regulations for respirator use (29 CFR 1910.134).
long sleeved clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable
Not available.
Polymerization occurs when exposed to white light, ultraviolet light or heat.
UV light. Extremes of temperature and direct sunlight.
Oxidizing agents. Heat, sunlight, or UV light. Polymerises in the presence of sunlight.
Thermal decomposition can lead to release of irritating gases and vapors. Oxides of carbon.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG?
The signal word is no signal word.
What is the physical form of LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG?
LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG is a solid with colourless / colorless to light yellow color. It has resinous odor.
What is the solubility of LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG?
Insoluble Water
What is LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG used for?
Pressure Sensitive Adhesives
What are the hazard statements for LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG?
This substance has 3 hazard statements:
- MOLTEN ADHESIVE MAY CAUSE SEVERE BURNS.
- STATIC CHARGES GENERATED BY EMPTYING PACKAGE IN OR NEAR FLAMMABLE VAPORS MAY CAUSE IGNITION.
- VAPORS ABOVE MOLTEN ADHESIVE MAY CAUSE EYE, SKIN AND RESPIRATORY TRACT IRRITATION.
What is the melting point of LOCTITE DURO-TAK UV 4194 ULTRA CAN 3KG?
The melting point is 60 - 150 °C (140°F - 302°F) calculated and the boiling point is Not applicable, Decomposes at 300°C (572°F)..