Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- AQUENCE EPIX BC 900F DR
- Product Code
- 2460090
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coating
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
If not breathing, give artificial respiration. Move to fresh air. Immediately remove victim to fresh air.
Immediately wash skin thoroughly with soap and water. Remove contaminated clothing and shoes. Rinse with running water and soap.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Flush eyes with plenty of water for at least 5 minutes.
Never give anything by mouth to an unconscious person.
Immediate Medical Attention
If symptoms persist, seek medical advice. Get immediate medical attention. Seek medical attention immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
carbon dioxide, foam, powder, water spray jet, fine water spray
This product is an aqueous mixture which will not burn. If evaporated to dryness, the solid residue may pose a slight fire hazard. In case of fire toxic gases can be released.
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Keep unnecessary personnel away. Wear respiratory protection equipment according to ambient air conditions.
Firefighter Protection
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Wear respiratory protection equipment according to ambient air conditions.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so. Do not allow material to contaminate ground water system. Do not allow product to enter sewer or waterways. Do not empty into drains / surface water / ground water / soil.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Remove with liquid-absorbing material (sand, peat, sawdust).
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust), liquid-absorbing material (sand, peat, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid skin and eye contact.
Do not freeze. Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in sealed original container. Store in a dry place.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use local ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits. Ensure good ventilation/extraction.
Use impermeable gloves and protective clothing as necessary to prevent skin contact. Use of Butyl or Nitrile Rubber gloves is recommended.
Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists. Safety showers and eye wash stations should be available. Wear protective glasses.
Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Suitable breathing mask when there is inadequate ventilation.
Use impermeable gloves and protective clothing as necessary to prevent skin contact. Wear protective equipment.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
Will not occur. None under normal processing.
Do not freeze. None if used for intended purpose.
Contact with water reactive materials (such as oleum) can cause exothermic reactions. None if used for intended purpose.
Oxides of carbon. Irritating organic vapours. No decomposition if used according to specifications.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for AQUENCE EPIX BC 900F DR?
The signal word is no signal word.
What is the physical form of AQUENCE EPIX BC 900F DR?
AQUENCE EPIX BC 900F DR is a liquid with light beige color. It has characteristic odor.
What is AQUENCE EPIX BC 900F DR used for?
Coating
What is the melting point of AQUENCE EPIX BC 900F DR?
The melting point is Not available. and the boiling point is Not available..