Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g)
- Product Code
- 1199831
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Electronic Materials LLC
manufacturer
14000 Jamboree Road, Irvine, CA 92606
1.888.9.HENKEL (1.888.943.6535)
www.henkel.com/electronics
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and footwear. Wash clothing before reuse. Get medical attention.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.
Never give anything by mouth to an unconscious person. Get medical attention.
Immediate Medical Attention
Get medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
This product is combustible at high temperatures. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.
In case of fire, keep containers cool with water spray.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. Refer to Section 8 'Exposure Controls / Personal Protection' prior to clean up.
Do not allow product to enter sewer or waterways.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up as much material as possible.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)
Related Products
Similar products with comparable safety profiles
LOCTITE ABLESTIK 8600 known as Abletherm 8600 (22g)
---
LOCTITE ABLESTIK 8600 known as Abletherm 8600 (22g)
---
LOCTITE ABLESTIK 12-1 known as Abletherm 12-1 (6.3g), Silicone adhesive
---
LOCTITE ABLESTIK 2600BT known as Abletherm 2600BT (9.3g)
---
LOCTITE ECCOBOND AA 01 known as Abletherm AA01 (45g)
---
LOCTITE ABLESTIK 2300 known as Ablebond 2300 (33g)
---
LOCTITE ABLESTIK 958-2 known as Ablebond 958-2 (15g)
---
LOCTITE ABLESTIK 968-2 known as Ablebond 968-2 (54g)
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only with adequate ventilation. Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling.
Store at or below -40.0 °C (-40°F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Keep container dry.
Wash thoroughly after handling.
Keep in a cool, well ventilated area away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions of storage and use.
Not available.
None under normal processing. Polymerization may occur at elevated temperature or in the presence of incompatible materials.
Elevated temperatures. Heat, flames, sparks and other sources of ignition. Avoid contact with water. Store away from incompatible materials.
Strong acids. Chlorine trifluoride. Phosphorus pentachloride. Bases. Oxidizing agents.
Magnesium oxide fumes. Oxides of carbon. Silicon dioxide. Formaldehyde.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- Environmentally hazardous substance, solid, n.o.s.
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g)?
The signal word is warning.
What is the physical form of LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g)?
LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g) is a paste with white color. It has odorless odor.
What are the hazard statements for LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g)?
This substance has 3 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H319: CAUSES SERIOUS EYE IRRITATION.
- H336: MAY CAUSE DROWSINESS OR DIZZINESS.
What is the melting point of LOCTITE ABLESTIK 12-2 known as Abletherm 12-2 (21g)?
The melting point is Not available. and the boiling point is Not available..