NextSDS Logo
Safety Data Sheet EN

Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig

CAS 999999-99-4
EC 310-127-6

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig
Chemical Name
Hydrous aluminium silicate
Synonyms
plastic clay, ball clay, fine clay

Regulatory Identifiers

CAS Number
999999-99-4 Check regulations →
EC Number
310-127-6 Check regulations →
REACH No.
Exempted in accordance with Annex V.7 of Regulation (EC) 1907/2006

Identified Uses

Ceramics (sanitaryware, floor tiles, wall tiles, roof tiles, tiles; porcelain, tableware, refractories, etc.), Enamels, Glass, Fillers, Deposit sealing, Paint, Plastic & Rubber, Adhesives and Sealant, Building material & Cement, Fertilisers & Agricultural products

Uses advised against

There is no use advised against.

Manufacturers & Suppliers

A

Arno Witgert, Inh. Dipl.-Ing. (FH) Michael Liebig e. K.

manufacturer

Arno-Witgert-Str. 1, 56414 Herschbach/OT Wahnscheid, Germany

0049 (0)6435/9223-0

Emergency Contacts

European Emergency N°

112

Emergency telephone at the company

0049 (0)6435/9223-0

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

Hazard Classifications

Not Classified

GHS Pictograms

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type uvcb
Chemical Name CAS Number Concentration Hazardous
Kaolinitic clay --- --- No
quartz-fine fraction EC: 238-878-4 14808-60-7 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Movement of the exposed individual from the area to fresh air is recommended.

Skin contact

No special first aid measures necessary.

Eye contact

Rinse under water for at least one minute and seek medical attention if irritation persists.

Ingestion

No first aid measure required.

Immediate Medical Attention

Seek medical attention if irritation persists (following eye contact).

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

No specific extinguishing media is needed.

Unsuitable media

No restriction on the extinguishing media to be used.

Specific hazards

None. The material is not flammable

Firefighter Protection

No specific fire-fighting protection is required.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Ensure adequate ventilation. Keep dust levels to a minimum. Keep unprotected persons away. Avoid contact with skin, eyes, and personal clothing. Avoid inhalation of dust. Take care of wet product on floor, which presents a slip hazard.

Environmental

No special environmental measures are necessary.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Keep dust levels to a minimum. Minimize dust generation. Handle packaged products carefully to prevent accidental bursting.

Storage

Keep containers closed and store packaged products so as to prevent accidental bursting.

Hygiene

General occupational hygiene measures are required to ensure safe handling of the substance. These measures involve good personal and housekeeping practices (i.e. regular cleaning with suitable cleaning devices), no drinking, eating and smoking in the work areas. Remove contaminated clothing and protective equipment before entering eating areas. Shower and change clothes at end of work shift. Do not wear contaminated clothing at home.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Minimise airborne dust generation. Use process enclosures, local exhaust ventilation or other engineering controls to keep airborne levels below specified exposure limits. If user operations generate dust, fumes or mist, use ventilation to keep exposure to airborne particles below the exposure limit. Apply organisational measures e.g. by isolating personnel from dusty areas.

Hands

For hands, appropriate protection (e.g. PVC, neoprene or natural rubber gloves) is recommended for workers who suffer from dermatitis or sensitive skin.

Eyes

Wear safety glasses with side-shields, or tight-fitting full-vision goggles in circumstances where there is a risk of penetrative eye injuries. Do not wear contact lenses.

Respiratory

Local ventilation to control airborne dust levels below occupational exposure limits is recommended. In case of prolonged exposure to airborne dust concentrations wear a respiratory protective equipment that complies with the requirements of European and national legislation. The use of a suitable particle filter mask type FFP1, FFP2 or FFP3 is recommended. See EN 143: 2000 (Respiratory Protective devices – Particle filters) and EN149: 2001 (Respiratory protective devices - Filtering half masks to protect against particles).

Skin/Body

For skin, normal work clothes are appropriate.

Environmental

All ventilation systems should be filtered before discharge to atmosphere. Avoid wind dispersal. Contain the spillage.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Flash Point
not applicable (solid with a melting point > 450 °C)
Boiling Point
not applicable (solid with a melting point > 450 °C)
Solubility
---
Physical State Data
solid
Lower Explosive Limit
do not apply to solids
Melting Point
> 450 °C (study result, EU A.1 method)
Decomposition Temperature
not applicable (solid with a melting point > 450 °C)
Bulk Density
---
Partition Coefficient
not applicable (inorganic substance)
Kinematic Viscosity
do not apply to solids (solid with a melting point > 450 °C)
Colour
grey
Density
---
Appearance
---
Relative Density
2.6 g/cm³
Auto Ignition Temperature
do not apply to solids
Relative Evaporation Rate
---
Evaporation Rate
not applicable (solid with a melting point > 450 °C)
Colour Intensity
---
State Under Standard Conditions
---
Dynamic Viscosity
---
Odor Threshold
---
Flammability
non flammable (study result, EU A.10 method)
Softening Point
---
Crystallisation Point
---
Metal Corrosion
---
Cloud Point
---
Upper Explosive Limit
do not apply to solids
Vapor Pressure
not applicable (solid with a melting point > 450 °C)
Solubility In Water
<1 mg/L at 20°C (study results, EU A.6 method)
Explosive Limits
---
Voc Content
---
Physical State
liquid (as aqueous suspension)
Form
---
Ph
3-7
Odor
odourless
Properties Status
---
Molecular Weight
---
Freezing Point
---
Solubility In Fat
---
Vapor Density
not applicable (solid with a melting point > 450 °C)
Solidification Point
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Kaolinitic clay is chemically stable.

Reactivity

Inert, not reactive.

Hazardous reactions

No hazardous reaction.

Avoid

None.

Incompatible

None.

Decomposition

None.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

ADR

Avoid any release of dust during transportation, by using air-tight tanks for powders and covered trucks for pebbles.

IMDG

Avoid any release of dust during transportation, by using air-tight tanks for powders and covered trucks for pebbles.

IATA

Avoid any release of dust during transportation, by using air-tight tanks for powders and covered trucks for pebbles.

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What other names is Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig known by?

Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig is also known as: plastic clay, ball clay, fine clay

What is the hazard signal word for Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig?

The signal word is no signal word.

What is the physical form of Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig?

Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig is a liquid (as aqueous suspension) with grey color. It has odourless odor.

What is Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig used for?

Ceramics (sanitaryware, floor tiles, wall tiles, roof tiles, tiles; porcelain, tableware, refractories, etc.), Enamels, Glass, Fillers, Deposit sealing, Paint, Plastic & Rubber, Adhesives and Sealant, Building material & Cement, Fertilisers & Agricultural products

What is the melting point of Steinzeug-Gießmasse Nr. 116, anthrazit, anwendungsfertig?

The melting point is > 450 °C (study result, EU A.1 method) and the boiling point is not applicable (solid with a melting point > 450 °C).