Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- FW UV / SOLVENT CLEANER 4
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Industrial cleaner
Manufacturers & Suppliers
Flexo Wash ApS
manufacturer
Grenaavej 631 K, 8541 Skoedstrup, Denmark
+ 45 86993631
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with non hazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Dipropyleneglycol methyl ether EC: 252-104-2 | 34590-94-8 | 35% | Yes |
| Isotridecanol, ethoxylated | 69011-36-5 | 3% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
No further relevant information available.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
No special measures required.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No special measures required.
None.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Only use chemical-protective gloves with CE-labelling of category III. To minimise the wetness in the glove due to perspiration changing of gloves during a shift is required. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. For the protection against chemicals in areas with heightened risk of injury (mechanical hazard) no recommendation for a suitable glove material can be given. Selection of the glove material on consideration of the penetration times, rates of diffusion and the Degradation. Material of gloves: Nitrile rubber, NBR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. For the mixture of chemicals mentioned below the penetration time has to be at least 60 minutes (Permeation according to EN 374 Part 3: Level 1). The determined penetration times according to EN 374 part III are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended. Value for the permeation: Level ≤ 1
Safety glasses
Not required.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for FW UV / SOLVENT CLEANER 4?
The signal word is warning.
What is the physical form of FW UV / SOLVENT CLEANER 4?
FW UV / SOLVENT CLEANER 4 is a liquid with clear color. It has specific type odor.
What is FW UV / SOLVENT CLEANER 4 used for?
Industrial cleaner
What are the hazard statements for FW UV / SOLVENT CLEANER 4?
This substance has 1 hazard statement:
- H319: Causes serious eye irritation.
What is the melting point of FW UV / SOLVENT CLEANER 4?
The melting point is Undetermined. and the boiling point is Undetermined..