PTC compounds all grades; RR compounds all grades.

Remove casualty to fresh air and keep warm and at rest. In case of doubt or persistent symptoms, consult always a physician.

Symptoms: Hot product (liquid) can cause thermal burns. Elevated temperatures or mechanical action may form vapours, mists or fumes which may be irritating to the eyes, nose, throat and lungs. Inhalation of dust may cause irritation of the respiratory system.

Cool melted product on skin with plenty of water. Do not remove solidified product. Get medical advice/attention.

Symptoms: Hot product (liquid) can cause thermal burns. Contact with dust may cause mechanical irritation or drying of the skin.

Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician. If eye irritation persists: Get medical advice/attention.

Symptoms: Hot product (liquid) can cause thermal burns. Dust may cause painful eye irritation and tearing.

Rinse mouth. Call a physician or poison control centre immediately.

Symptoms: May cause gastrointestinal irritation, nausea, vomiting and diarrhoea.

Water spray, Alcohol resistant foam, Carbon dioxide, Dry extinguishing powder.

Strong water jet.

Non flammable. Risk of dust explosion. Do not allow run-off from fire-fighting to enter drains or water courses.

Evacuate area. Use water spray or fog for cooling exposed containers. Contain the extinguishing fluids by bunding. Prevent fire fighting water from entering the environment.

Provide adequate ventilation. In case of large spillages: (Molten form). Evacuate personnel to a safe area. Risk of thermal burns on contact with molten product. Do not breathe dust. Avoid contact with skin, eyes and clothing. Use personal protective equipment as required. Ensure procedures and training for emergency decontamination and disposal are in place.

In case of large spillages: (Molten form). Evacuate personnel to a safe area.

Do not allow to enter into surface water or drains.

Take up mechanically (sweeping, shovelling) and collect in suitable container for disposal.

Provide adequate ventilation. Do not breathe dust. Avoid contact with skin, eyes and clothing. Use personal protective equipment as required. Concerning personal protective equipment to use, see section 8. Avoid dust formation. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Take precautionary measures against static discharges. Ensure proper process control to avoid excess waste discharge (temperature, concentration, pH, time). Take any precaution to avoid mixing with Incompatible materials, Refer to Section 10 on Incompatible Materials. Do not allow to enter into surface water or drains.

Store in a dry, cool and well-ventilated place. Keep at temperatures below 100 °C. Molten form : Keep under inert gas. nitrogen. Steam . Hazardous fumes may be released above 180 °C. Do not store near or with any of the incompatible materials listed in section 10.

Keep good industrial hygiene. Wash hands and face before breaks and immediately after handling of the product. When using do not eat, drink or smoke. Remove contaminated clothing and shoes.

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Take precautionary measures against static discharges.

Use only in area provided with appropriate exhaust ventilation. Apply measures to prevent dust explosions. Provide adequate precautions, such as electrical grounding and bonding, or inert atmospheres. Organisational measures to prevent /limit releases, dispersion and exposure. See also section 7 .

The selection of specific gloves for a specific application and time of use in a working area, should also take into account other factors on the working space, such as (but not limited to): other chemicals that are possibly used, physical requirements (protection against cutting/drilling, skill, thermal protection), and the instructions/specification of the supplier of gloves. Wear chemically resistant gloves (tested to EN374) . NBR (Nitrile rubber). Breakthrough time : >8h. Thickness > 0,3 mm

Safety glasses (EN 166)

In case of insufficient ventilation, wear suitable respiratory equipment. Effective dust mask (EN 149). Half-face mask (DIN EN 140). full face mask (DIN EN 136). Filter type: A/P (EN 141)

Wear suitable protective clothing. Overall. Chemical resistant safety shoes .

Avoid release to the environment. Comply with applicable Community environmental protection legislation.

The product is stable under storage at normal ambient temperatures.

None under normal processing. Reference to other sections: 10.4 & 10.5.

Potential dust explosion hazard.

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid dust formation.

oxidising substances. Strong acids. Fluorine.

Hazardous decomposition products formed under fire conditions. Reference to other sections 5.2.