Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Buffer solution pH 10.00 (20 GRAD C) Certipur®
- Product Code
- 1.09438
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- KRD1-P6MM-4997-JF10
Identified Uses
Reagent for analysis
Uses advised against
This product is not intended for consumer use.
Manufacturers & Suppliers
Merck Life Science UK Limited
national supplier
New Road, The Old Brickyard, GILLINGHAM, Dorset, SP8 4XT, UNITED KINGDOM
+44 (0)1747 833-000
Emergency Contacts
CHEMTREC
+44 (0)870 8200418
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| orthoboric acid, sodium salt (1:n) EC: 237-560-2 | 13840-56-7 | 0.3 - 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air. Call in physician.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician.
After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
For this substance/mixture no limitations of extinguishing agents are given.
Not combustible. Ambient fire may liberate hazardous vapours.
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Firefighter Protection
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up carefully with liquid-absorbent material. Clean up affected area.
Materials: liquid-absorbent material (e.g. Chemizorb®)
Related Products
Similar products with comparable safety profiles
Buffer solution pH 7.00 (20 GRAD C) Certipur®
---
Buffer Solution, pH 10.00
---
Buffer Solution pH 10.01 +/- 0.02 @ 25°C
CAS: Not applicable
Buffer Solution pH 10.01 ± 0.02
---
Buffer solution (citric acid/sodium hydroxide/hydrogen chloride) colour: red traceable to SRM from NIST and PTB pH 4.00 (20 °C) Certipur®
---
Buffer solution pH10,00(+/-0,05), conserved
UFI: 01WV-HPYF-KA74-3DRU
Buffer solution pH 10 (borate) Traceable to NIST
UFI: QSPA-62GT-UX0U-VCHF
Buffer Solution (Borate) pH 10 Blue
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not inhale substance/mixture.
Tightly closed. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons. Recommended storage temperature see product label.
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact Material: Nitrile rubber Minimum layer thickness: 0.11 mm Break through time: 480 min Material tested: KCL 741 Dermatril® L Splash contact Material: Nitrile rubber Minimum layer thickness: 0.11 mm Break through time: 480 min Material tested: KCL 741 Dermatril® L This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
required when vapours/aerosols are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type ABEK The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
protective clothing
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature) .
No data available
Violent reactions possible with: The generally known reaction partners of water.
no information available
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Buffer solution pH 10.00 (20 GRAD C) Certipur®?
The signal word is danger.
What is the physical form of Buffer solution pH 10.00 (20 GRAD C) Certipur®?
Buffer solution pH 10.00 (20 GRAD C) Certipur® is a liquid with colorless color. It has odorless odor.
What is Buffer solution pH 10.00 (20 GRAD C) Certipur® used for?
Reagent for analysis
What are the hazard statements for Buffer solution pH 10.00 (20 GRAD C) Certipur®?
This substance has 1 hazard statement:
- H360: H360FD May damage fertility. May damage the unborn child.
What is the melting point of Buffer solution pH 10.00 (20 GRAD C) Certipur®?
The melting point is Melting point: -6 °C and the boiling point is 110 °C at 1,013 hPa.