Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Immersion oil for microscopy
- Product Code
- 1.04699
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- This product is a mixture. REACH Registration Number see section 3.
- UFI Code
- 0F32-R681-M99E-WTFA
Identified Uses
In vitro diagnostic reagent, Reagent for analysis
Uses advised against
This product is not intended for consumer use.
Manufacturers & Suppliers
Merck Life Science BV/SRL
manufacturer
Brusselsesteenweg 288, B-3090 OVERIJSE
+32 (0)3 899-1301
Emergency Contacts
CHEMTREC
+(32) 28 083237
Anti-poison centre
070 245245
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Benzyl benzoate EC: 204-402-9 | 120-51-4 | 30 - 50% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most).
Immediate Medical Attention
Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water Foam Carbon dioxide (CO2) Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Combustible. Development of hazardous combustion gases or vapours possible in the event of fire.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapors, aerosols. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up with liquid-absorbent material (e.g. Chemizorb®). Clean up affected area.
Materials: liquid-absorbent material (e.g. Chemizorb®)
Related Products
Similar products with comparable safety profiles
Microscopes-Immersion Liquids for Light Microscopy
---
Immersion Oil, 150 CS
---
Cargille Immersion Oil
---
Cargille Immersion Oil Type A / Type B
---
Cargille Immersion Oil Type A, Cargille Immersion Oil Type B
---
Cargille Immersion Oil Type A / Cargille Immersion Oil Type B
---
DPX new non-aqueous mounting medium for microscopy
---
DPX new non-aqueous mounting medium for microscopy
UFI: RY2Y-J5KR-299H-J1V2
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed. Recommended storage temperature see product label.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: butyl-rubber, Minimum layer thickness: 0,7 mm, Break through time: 480 min, Material tested: Butoject® (KCL 898). Splash contact: Material: Chloroprene, Minimum layer thickness: 0,65 mm, Break through time: 30 min, Material tested: KCL 720 Camapren®.
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Not required; except in case of aerosol formation.
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature) .
No data available
Violent reactions possible with: Strong oxidizing agents
no information available
various plastics, Light metals, metal alloys
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Benzyl benzoate)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Immersion oil for microscopy?
The signal word is warning.
What is the physical form of Immersion oil for microscopy?
Immersion oil for microscopy is a liquid with light yellow color. It has characteristic odor.
What is Immersion oil for microscopy used for?
In vitro diagnostic reagent, Reagent for analysis
What are the hazard statements for Immersion oil for microscopy?
This substance has 1 hazard statement:
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of Immersion oil for microscopy?
The melting point is No data available and the boiling point is No data available.