NextSDS Logo
Safety Data Sheet EN

Floreal Fresh

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Floreal Fresh

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Greenspeed logo

Greenspeed

manufacturer

Cobbenhagenstraat 26, 2288 ET Rijswijk (ZH), NL

+31703458737

http://www.greenspeed.eu/

Emergency Contacts

Emergency Contact

03451 302230

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Eye Irrit. Cat. 2 H319
EUH208

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H319 Causes serious eye irritation.

Precautionary Statements

P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 If eye irritation persists: Get medical advice/attention.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
alcohols, C10-16, ethoxylated, propoxylated 69227-22-1 5 - 15% Yes
D-Glucopyranose, C10-16(even numbered)-alkyl glycosides EC: 600-975-8 110615-47-9 5% Yes
C8-10 D-glucoside EC: 500-220-1 68515-73-1 5% Yes
Sodiumlaurylsulphate EC: 273-257-1 68955-19-1 5% Yes
alpha-Pinene EC: 232-077-3 7785-26-4 5% Yes
1,8-Cineole EC: 207-431-5 470-82-6 5% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

let sit upright, fresh air, rest and take to hospital.

Skin contact

remove contaminated clothing, rinse skin with plenty of water and immediately transport to hospital.

Eye contact

first prolonged rinsing with water (contact lenses to be removed if this is easily done) then take to physician.

Symptoms: redness, pain, bad looking

Ingestion

rinse mouth, do not induce vomiting, take to hospital immediately.

Symptoms: diarrhoea, headache, abdominal cramps, sleepiness, vomiting

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

CO2, foam, powder, sprayed water

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Do not walk into or touch spilled substances and avoid inhalation of fumes, smoke, dusts and vapours by staying up wind. Remove any contaminated clothing and used contaminated protective equipment and dispose of it safely.

Environmental

do not allow to flow into sewers or open water.

Cleanup methods

remove by using absorbent material.

Materials: absorbent material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

handle with care to avoid spillage.

Storage

keep in a sealed container in a closed, frost-free, ventilated room.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

If necessary, use with sufficient exhaust ventilation.

Hands

handling with nitril-gloves (EN 374). Breakthrough time: >480' Material thickness: 0,35 mm. Thoroughly check gloves before use. Take of the gloves properly without touching the outside with your bare hands. The manufacturer of the protective gloves has to be consulted about the suitability for a specific work station.

Eyes

Tight-fitting safety goggles. Wear a face shield

Respiratory

respiratory protection is not required. Use ABEK type gas masks in case of irritating exposure.

Skin/Body

protective suit in case of exceptional processing problems. impermeable clothing. The type of protective equipment depends on the concentration and amount of hazardous substances at the work station in question.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Melting Point
0 °C
Dynamic Viscosity
1 mPa.s
Flammability
not applicable
Ph
8.0
Solubility In Water
not soluble
Boiling Point
100 °C
State Under Standard Conditions
---
Odor
characteristic
Relative Evaporation Rate
---
Metal Corrosion
---
Freezing Point
---
Density
---
Form
---
Vapor Pressure
2 332 Pa
Appearance
liquid
Physical State
liquid
Colour
---
Lower Explosive Limit
/
Partition Coefficient
not applicable
Decomposition Temperature
/
Solidification Point
---
Solubility
---
Vapor Density
not applicable
Softening Point
---
Relative Density
1.015 kg/l
Properties Status
---
Cloud Point
---
Explosive Limits
---
Molecular Weight
---
Bulk Density
---
Upper Explosive Limit
/
Crystallisation Point
---
Evaporation Rate
0.300
Auto Ignition Temperature
/
Solubility In Fat
---
Physical State Data
liquid
Odor Threshold
not applicable
Colour Intensity
---
Kinematic Viscosity
1 mm²/s
Flash Point
/
Voc Content
9.804 g/l
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

extremely high or low temperatures

Reactivity

stable under normal conditions.

Avoid

protect from sunlight and do not expose to temperatures exceeding + 50°C.

Incompatible

acids, alkalines, oxidants, reductants

Decomposition

doesn't decompose with normal use

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Floreal Fresh?

The signal word is warning.

What is the physical form of Floreal Fresh?

Floreal Fresh is a liquid appearing as liquid . It has characteristic odor.

What are the hazard statements for Floreal Fresh?

This substance has 1 hazard statement:

  • H319: Causes serious eye irritation.

What is the melting point of Floreal Fresh?

The melting point is 0 °C and the boiling point is 100 °C.