NETTOYANT SILICONE 300ML U2

In the event of massive inhalation, remove the person exposed to fresh air. Keep warm and at rest. If the person is unconscious, place in recovery position. If breathing is irregular or has stopped, effect mouth-to-mouth resuscitation and call a doctor.

Remove contaminated clothing and wash the skin thoroughly with soap and water or a recognised cleaner. Watch out for any remaining product between skin and clothing, watches, shoes, etc.

Symptoms: Allergic reaction, widespread contamination, damage to the skin.

Wash thoroughly with fresh, clean water for 15 minutes holding the eyelids open.

Do not give the patient anything orally. If the quantity is small (no more than one mouthful), rinse the mouth with water and consult a doctor. Keep the person exposed at rest. Do not force vomiting. Seek medical attention immediately, showing the label. If swallowed accidentally, call a doctor to ascertain whether observation and hospital care will be necessary. If swallowed accidentally, do not allow to drink, do not induce vomiting and transfer to hospital immediately by ambulance.

sprayed water or water mist, water with AFFF (Aqueous Film Forming Foam) additive, foam, multipurpose ABC powder, BC powder, carbon dioxide (CO2)

water jet

Pressurised containers may burst when heated.

Keep packages near the fire cool, to prevent pressurised containers from bursting.

Eliminate sources of ignition and ventilate the area. Avoid inhaling the vapors. Avoid any contact with the skin and eyes. If a large quantity has been spilt, evacuate all personnel and only allow intervention by trained operators equipped with safety apparatus.

If a large quantity has been spilt, evacuate all personnel and only allow intervention by trained operators equipped with safety apparatus.

Contain and control the leaks or spills with non-combustible absorbent materials such as sand, earth, vermiculite, diatomaceous earth in drums for waste disposal.

Clean preferably with a detergent, do not use solvents.

Materials: detergent

Always wash hands after handling. Remove and wash contaminated clothing before re-using. Remove contaminated clothing and protective equipment before entering eating areas. Never inhale this mixture. Do not spray on a naked flame or any incandescent material. Do not pierce or burn, even after use. Do not smoke, eat or drink in areas where the mixture is used.

Keep packages tightly closed and away from sources of heat, sparks and naked flames. Packages which have been opened must be reclosed carefully and stored in an upright position.

Always wash hands after handling. Remove and wash contaminated clothing before re-using. Remove contaminated clothing and protective equipment before entering eating areas. No smoking, eating or drinking in areas where the mixture is used.

Handle in well-ventilated areas. Do not spray on a naked flame or any incandescent material. Keep packages tightly closed and away from sources of heat, sparks and naked flames. Do not use tools which may produce sparks. Do not smoke.

Ensure that there is adequate ventilation, especially in confined areas.

Use suitable protective gloves that are resistant to chemical agents in accordance with standard EN ISO 374-1. Gloves must be selected according to the application and duration of use at the workstation. Protective gloves need to be selected according to their suitability for the workstation in question : other chemical products that may be handled, necessary physical protections (cutting, pricking, heat protection), level of dexterity required. Type of gloves recommended : - Nitrile rubber (butadiene-acrylonitrile copolymer rubber (NBR)) - PVA (Polyvinyl alcohol) Let the glove manufacturer advise you on the choice of gloves and their duration of use for your operating conditions

Avoid contact with eyes. Use eye protectors designed to protect against liquid splashes. Before handling, wear safety goggles in accordance with standard ISO 16321.

Avoid inhaling vapors. If the ventilation is insufficient, wear appropriate breathing apparatus. When workers are confronted with concentrations that are above occupational exposure limits, they must wear a suitable, approved, respiratory protection device. Type of FFP mask : Wear a disposable half-mask aerosol filter in accordance with standard EN149/A1. Category : - FFP1 - FFP1 Anti-gas and vapour filter(s) (Combined filters) in accordance with standard EN14387 : - A1 (Brown) - AX Particle filter according to standard EN143 : - P1 (White) - P1 Types, classes and filters for respiratory protection above are recommended in case of confrontation at concentrations higher than the exposure limits specified under 8.1. (Control parameters) .They should be adjusted according to actual conditions. they may not be necessary if the product is used outdoors or in a well ventilated area.

Avoid skin contact. Wear suitable protective clothing. Suitable type of protective clothing : In the event of substantial spatter, wear liquid-tight protective clothing against chemical risks (type 3) in accordance with EN14605/A1 to prevent skin contact. In the event of a risk of splashing, wear protective clothing against chemical risks (type 6) in accordance with EN13034/A1 to prevent skin contact. Work clothing worn by personnel shall be laundered regularly.

This mixture is stable under the recommended handling and storage conditions in section 7.

No data available.

When exposed to high temperatures, the mixture can release hazardous decomposition products.

high temperatures

No incompatible materials known.

carbon monoxide and dioxide, fumes and nitrogen oxide

Stowage: SW1 SW22, Segregation: SG69