Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MAXX Forte2
- Product Code
- 116323E
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Floor Stripper
Uses advised against
Reserved for industrial and professional use.
Manufacturers & Suppliers
Ecolab Ltd.
manufacturer
PO Box 11; Winnington Avenue Northwich, Cheshire, United Kingdom CW8 4DX
+ 44 (0)1606 74488
Emergency Contacts
Emergency Contact
+441618841235
Trans-European
+32-(0)3-575-5555
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Sodium p-cumenesulphonate EC: 239-854-6 | 15763-76-5 | 3 - 5% | Yes |
| 2-phenoxyethanol EC: 204-589-7 | 122-99-6 | 1 - 2.5% | Yes |
| diphosphoric acid, tetrapotassium salt EC: 230-785-7 | 7320-34-5 | 1 - 2.5% | Yes |
| 2-(2-butoxyethoxy)ethanol EC: 203-961-6 | 112-34-5 | 1 - 2.5% | Yes |
| Alcohols, C12-18, ethers with polyethylene glycol mono-Bu ether | 146340-16-1 | 1 - 2.5% | Yes |
| Dipropylene glycol methyl ether EC: 252-104-2 | 34590-94-8 | 5 - 10% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Rinse with plenty of water.
Rinse with plenty of water.
Rinse mouth.
Immediate Medical Attention
Get medical attention if symptoms occur.
Medical Treatment
No specific measures identified.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
None known.
Not flammable or combustible.
Firefighter Protection
Use personal protective equipment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Advice for non-emergency personnel : Refer to protective measures listed in sections 7 and 8. Advice for emergency responders : If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials.
For large spills, dike spilled material or otherwise contain material to ensure runoff does not reach a waterway.
No special environmental precautions required.
Stop leak if safe to do so. Contain spillage, and then collect with non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and place in container for disposal according to local / national regulations (see section 13). Flush away traces with water.
Materials: non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wash hands after handling. In case of mechanical malfunction, or if in contact with unknown dilution of product, wear full Personal Protective Equipment (PPE). For personal protection see section 8.
Keep out of reach of children. Keep container tightly closed. Store in suitable labeled containers.
Wash hands before breaks and immediately after handling the product.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.
No special protective equipment required.
No special protective equipment required.
None required if airborne concentrations are maintained below the exposure limit listed in Exposure Limit Information. Use certified respiratory protection equipment meeting EU requirements(89/656/EEC, (EU) 2016/425), or equivalent, when respiratory risks cannot be avoided or sufficiently limited by technical means of collective protection or by measures, methods or procedures of work organization.
No special protective equipment required.
Consider the provision of containment around storage vessels.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
No dangerous reaction known under conditions of normal use.
No dangerous reaction known under conditions of normal use.
None known.
Noble metals
Depending on combustion properties, decomposition products may include following materials: Carbon oxides, Sulphur oxides, Oxides of phosphorus, metal oxides
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MAXX Forte2?
The signal word is no signal word.
What is the physical form of MAXX Forte2?
MAXX Forte2 is a liquid appearing as liquid with clear, colourless color. It has ammoniacal odor.
What is MAXX Forte2 used for?
Floor Stripper
What is the melting point of MAXX Forte2?
The melting point is Not applicable and/or not determined for the mixture and the boiling point is > 100 °C.