Dimethylformamide

Remove to fresh air. If breathing is difficult, give oxygen.

Symptoms: Difficulty in breathing.

Wash off immediately with plenty of water for at least 15 minutes.

Symptoms: May be harmful if absorbed through skin

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.

Symptoms: Irritating to eyes.

Do NOT induce vomiting.

Symptoms: Gastrointestinal discomfort

Water spray, carbon dioxide (CO2), dry chemical, alcohol-resistant foam. Water mist may be used to cool closed containers.

Do not use water jetstream.

Flammable. Risk of ignition. Containers may explode when heated. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Thermal decomposition can lead to release of irritating gases and vapors.

As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.

Ensure adequate ventilation. Use personal protective equipment as required. Keep people away from and upwind of spill/leak. Evacuate personnel to safe areas.

Should not be released into the environment. See Section 12 for additional Ecological Information.

Soak up with inert absorbent material. Keep in suitable, closed containers for disposal.

Materials: inert absorbent material

Use only under a chemical fume hood. Wear personal protective equipment/face protection. Do not get in eyes, on skin, or on clothing. Do not breathe mist/vapors/spray. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. Use spark-proof tools and explosion-proof equipment. Take precautionary measures against static discharges.

Keep containers tightly closed in a dry, cool and well-ventilated place.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools.

Use only under a chemical fume hood. Ensure that eyewash stations and safety showers are close to the workstation location. Use explosion-proof electrical/ventilating/lighting equipment. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Butyl rubber (> 480 minutes, 0.5 mm, EN 374), Neoprene (< 100 minutes, 0.45 mm). As tested under EN374-3 Determination of Resistance to Permeation by Chemicals.

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Type A Organic gases and vapours filter Brown conforming to EN14387. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask:- Valve filtering: EN405; or; Half mask: EN140; plus filter, EN 141. When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure.

Prevent product from entering drains.

Stable under normal conditions.

None known, based on information available

None under normal processing. Hazardous polymerization does not occur.

Incompatible products. Heat, flames and sparks. Keep away from open flames, hot surfaces and sources of ignition.

Strong oxidizing agents. Halogens. Halogenated compounds. Reducing Agent. . Alkali metals.

Carbon monoxide (CO). Carbon dioxide (CO₂). Nitrogen oxides (NOx).