1-Chloromethyl-4-fluoro-1,4-diazoniabicyclo[2.2.2]octane bis(tetrafluoroborate)

Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur.

Symptoms: Trouble breathing, dizziness, lightheadedness, chest pain.

Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician.

Symptoms: May cause allergic skin reaction. Symptoms of allergic reaction may include rash, itching, swelling, tingling of the hands and feet, muscle pain or flushing.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Symptoms: Causes severe eye damage.

Clean mouth with water and drink afterwards plenty of water. Get medical attention if symptoms occur.

Carbon dioxide (CO₂). Dry chemical.

No information available.

Thermal decomposition can lead to release of irritating gases and vapors.

Ensure adequate ventilation. Use personal protective equipment as required.

Should not be released into the environment.

Sweep up and shovel into suitable containers for disposal.

Materials: suitable containers

Wear personal protective equipment/face protection. Ensure adequate ventilation. Do not get in eyes, on skin, or on clothing. Avoid ingestion and inhalation. Avoid dust formation.

Keep in a dry, cool and well-ventilated place. Keep container tightly closed. Keep away from heat, sparks and flame. Keep at temperature not exceeding 30°C. Corrosives area. Keep under nitrogen.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from heat, sparks and flame.

Ensure adequate ventilation, especially in confined areas. Ensure that eyewash stations and safety showers are close to the workstation location. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Natural rubber, Nitrile rubber, Neoprene, PVC. Breakthrough time: See manufacturers recommendations. EU standard: EN 374. (minimum requirement)

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced Recommended Filter type: Particulates filter conforming to EN 143. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask:- Particle filtering: EN149:2001 When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure. Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. (Refer to manufacturer/supplier for information) Ensure gloves are suitable for the task: Chemical compatibility, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Prevent product from entering drains.

Unstable if heated. Moisture sensitive.

Yes

Hazardous polymerization does not occur. None under normal processing.

Temperatures above 50°C. Keep away from open flames, hot surfaces and sources of ignition. Incompatible products. Exposure to moist air or water. Combustible material.

Incompatible products. Combustible material.

Nitrogen oxides (NOx). Carbon monoxide (CO). Carbon dioxide (CO₂). Gaseous hydrogen fluoride (HF). Oxides of boron.