NextSDS Logo
Safety Data Sheet EN

PROVISIONS READY MATCH Touchup

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
PROVISIONS READY MATCH Touchup
Product Form
Aerosol.
Product Code
168-0842

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Paint or paint related material.

Manufacturers & Suppliers

T

The Sherwin-Williams Company

manufacturer

1 Sherwin Way, Cleveland, OH 44113

1-800-474-3794

Emergency Contacts

Emergency Contact

(800) 424-9300

SETIQ

800-00-214-00

Available 24 hours and 365 days a year

SETIQ

55-5559-1588

Available 24 hours and 365 days a year

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Aerosol Cat. 1
Eye Irrit. Cat. 2A
Carc. Cat. 2
STOT SE Cat. 3
STOT RE Cat. 2

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H222 Extremely flammable aerosol.
H229 Pressurized container: may burst if heated.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
H351 Suspected of causing cancer.
H372 May cause damage to organs through prolonged or repeated exposure.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P233 Keep container tightly closed.
P251 Do not pierce or burn, even after use.
P261 Do not breathe dust or mist.
P264 Wash thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves, protective clothing and eye or face protection.
P304 + P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical advice or attention.
P312 Call a POISON CENTER or doctor if you feel unwell.
P337 + P313 If eye irritation persists: Get medical advice or attention.
P403 Store in a well-ventilated place.
P405 Store locked up.
P410 Protect from sunlight.
P411 Do not expose to temperatures exceeding 122 °F/50 °C.
P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Acetone 67-64-1 15 - 40% No
Propane 74-98-6 10 - 30% No
Barium Sulfate 7727-43-7 7 - 13% No
2-methoxy-1-methylethyl acetate 108-65-6 7 - 13% No
Butane 106-97-8 5 - 10% No
n-Butyl Acetate 123-86-4 1 - 5% No
Titanium Dioxide 13463-67-7 1 - 5% No
Xylene, mixed isomers 1330-20-7 1 - 5% No
Methyl n-Propyl Ketone 107-87-9 1 - 5% No
Ethylbenzene 100-41-4 0.1 - 1% No

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Notes

Any concentration shown as a range is to protect confidentiality or is due to batch variation.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If necessary, call a poison center or physician. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Symptoms: Can cause central nervous system (CNS) depression. May cause drowsiness or dizziness. Adverse symptoms may include the following: respiratory tract irritation, coughing, nausea or vomiting, headache, drowsiness/fatigue, dizziness/vertigo, unconsciousness.

Skin contact

Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse.

Symptoms: No known significant effects or critical hazards. No specific data.

Eye contact

Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.

Symptoms: Causes serious eye irritation. Adverse symptoms may include the following: pain or irritation, watering, redness.

Ingestion

Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. If necessary, call a poison center or physician. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Symptoms: Can cause central nervous system (CNS) depression. No specific data.

Immediate Medical Attention

Get medical attention.

Medical Treatment

No specific treatment.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use an extinguishing agent suitable for the surrounding fire.

Unsuitable media

None known.

Specific hazards

Extremely flammable aerosol. Runoff to sewer may create fire or explosion hazard. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Gas may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back, causing fire or explosion. Bursting aerosol containers may be propelled from a fire at high speed.

Instructions

Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool.

Firefighter Protection

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. In the case of aerosols being ruptured, care should be taken due to the rapid escape of the pressurized contents and propellant. If a large number of containers are ruptured, treat as a bulk material spillage according to the instructions in the clean-up section. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Do not breathe dust or mist. Put on appropriate personal protective equipment.

Small spill

Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Absorb with an inert material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.

Large spill

Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations.

Environmental

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Put on appropriate personal protective equipment (see Section 8). Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50°C. Do not pierce or burn, even after use. Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not ingest. Avoid breathing gas. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Empty containers retain product residue and can be hazardous.

Storage

Store in accordance with local regulations. Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Eliminate all ignition sources. Use appropriate containment to avoid environmental contamination.

Hygiene

Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas.

Fire prevention

Store and use away from heat, sparks, open flame or any other ignition source. Eliminate all ignition sources.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Solidification Point
---
Solubility
---
Auto Ignition Temperature
Not available.
Odor
Not available.
Bulk Density
---
Softening Point
---
Colour
Various
Ph
Not applicable.
Kinematic Viscosity
Kinematic (40°C (104°F)): >20.5 mm2/s (>20.5 cSt)
Crystallisation Point
---
Vapor Pressure
101.3 kPa (760 mm Hg)
Partition Coefficient
Not applicable.
Evaporation Rate
5.6 (butyl acetate = 1)
Melting Point
Not available.
Density
0.86 g/cm³
Relative Evaporation Rate
---
Molecular Weight
Not applicable.
Flash Point
Closed cup: -29°C (-20.2°F) [Pensky-Martens Closed Cup]
Relative Density
0.86
Boiling Point
Not available.
Flammability
Flammable aerosol.
Appearance
Liquid. Various
Solubility In Fat
---
State Under Standard Conditions
---
Voc Content
---
Freezing Point
---
Properties Status
---
Colour Intensity
---
Metal Corrosion
---
Dynamic Viscosity
Dynamic (room temperature): Not available.
Cloud Point
---
Upper Explosive Limit
Upper: 13.1%
Decomposition Temperature
Not available.
Form
---
Explosive Limits
---
Odor Threshold
Not available.
Physical State
Liquid.
Vapor Density
---
Solubility In Water
Not soluble
Lower Explosive Limit
Lower: 1%
Physical State Data
aerosol
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

The product is stable.

Reactivity

No specific test data related to reactivity available for this product or its ingredients.

Hazardous reactions

Under normal conditions of storage and use, hazardous reactions will not occur.

Avoid

Avoid all possible sources of ignition (spark or flame).

Incompatible

No specific data.

Decomposition

Under normal conditions of storage and use, hazardous decomposition products should not be produced.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1950
Shipping Name
AEROSOLS
Transport Class
2.1
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for PROVISIONS READY MATCH Touchup?

The signal word is danger.

What is the physical form of PROVISIONS READY MATCH Touchup?

PROVISIONS READY MATCH Touchup is a liquid. appearing as liquid. various with various color. It has not available. odor.

What is PROVISIONS READY MATCH Touchup used for?

Paint or paint related material.

What are the hazard statements for PROVISIONS READY MATCH Touchup?

This substance has 6 hazard statements:

  • H222: Extremely flammable aerosol.
  • H229: Pressurized container: may burst if heated.
  • H319: Causes serious eye irritation.
  • H336: May cause drowsiness or dizziness.
  • H351: Suspected of causing cancer.
  • H372: May cause damage to organs through prolonged or repeated exposure.

What is the melting point of PROVISIONS READY MATCH Touchup?

The melting point is Not available. and the boiling point is Not available..