Phenol

After inhalation: fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen.

After contact with skin: rinse out with polyethylene glycol 400 or a mixture of polyethylene glycol 300/ethanol 2:1 and wash with plenty of water. If neither is available wash with plenty of water. Immediately take off contaminated clothing. Call a physician immediately.

After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist. Remove contact lenses.

If swallowed: give water to drink (two glasses at most). Seek medical advice immediately. In exceptional cases only, if medical care is not available within one hour, induce vomiting (only in persons who are wide awake and fully conscious), administer activated charcoal (20 - 40 g in a 10% slurry) and consult a doctor as quickly as possible. Do not attempt to neutralise.

Water Foam Carbon dioxide (CO2) Dry powder

For this substance/mixture no limitations of extinguishing agents are given.

Combustible. Vapours are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating. Development of hazardous combustion gases or vapours possible in the event of fire.

Remove container from danger zone and cool with water.

Avoid generation and inhalation of dusts in all circumstances. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains.

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully. Dispose of properly. Clean up affected area.

Work under hood. Do not inhale substance/mixture.

Tightly closed. Dry. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorised persons.

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharge.

Material : Viton® Break through time : 480 min Glove thickness : 0,7 mm Protective index : Full contact Manufacturer : Vitoject® (KCL 890 / Aldrich Z677698, Size M) Material : Viton® Break through time : 480 min Glove thickness : 0,7 mm Protective index : Splash contact Manufacturer : Vitoject® (KCL 890 / Aldrich Z677698, Size M) Remarks : This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles

required when dusts/vapours/aerosols are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter A-(P3) The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

Flame retardant antistatic protective clothing.

Do not let product enter drains.

The product is chemically stable under standard ambient conditions (room temperature).

Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical. The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

Exothermic reaction with: Aluminium, Aldehydes, halogens, hydrogen peroxide, iron(III) compounds, Oxidizing agents, Strong acids, Strong bases, formaldehyde. Risk of explosion with: nitrites, nitrates, salts of oxyhalogenic acids, peroxi compounds.

Strong heating.

No data available

In the event of fire: see section 5