Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide
- Product Code
- D0815
Regulatory Identifiers
- CAS Number
- 3785-01-1 Check regulations →
Identified Uses
Laboratory chemicals, Manufacture of substances
Manufacturers & Suppliers
Merck Life Science BV
manufacturer
Ildefonse Vandammestraat 5/7B B-1560 HOEILAART
+32 (0)3 899-1301
Emergency Contacts
CHEMTREC
+(32) 28 083237
Anti-poison centre
070 245245
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Substance name : DASPEI EC-No. : 223-248-3
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| DASPEI EC: 223-248-3 | --- | --- | No |
Notes
Remarks : No hazardous ingredients
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most).
Immediate Medical Attention
Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water, Foam, Carbon dioxide (CO2), Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Combustible. Development of hazardous combustion gases or vapours possible in the event of fire.
Suppress (knock down) gases/vapours/mists with a water spray jet.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Cover drains. Collect, bind, and pump off spills. Take up dry. Clean up affected area.
Related Products
Similar products with comparable safety profiles
4-(Dimethylamino)pyridine
CAS: 1122-58-3
(1-Hexadecyl)pyridinium chloride monohydrate
CAS: 6004-24-6
2-Chloro-6-(trichloromethyl)pyridine
CAS: 1929-82-4
Methyl 3-bromoimidazo[1,5-a]pyridine-1-carboxylate
CAS: 1039357-00-0
1,3,3-trimethyl-2-((1E,3E)-5-((E)-1,3,3-trimethylindolin-2-ylidene)penta-1,3dien-1-yl)-3H-indol-1-ium perchlorate
CAS: 81666-87-7
Ethyl 7-chloroimidazo[1,2-c]-pyrimidine-2-carboxylate
CAS: 1105187-40-3
5-Ethyl-2-methylpyridine
---
4-IODO-1,2-DIMETHOXYBENZENE
CAS: 5460-32-2
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Change contaminated clothing. Wash hands after working with substance. For precautions see section 2 GHS label elements
Tightly closed. Dry.
Change contaminated clothing. Wash hands after working with substance.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Material : Nitrile rubber Break through time : 480 min Glove thickness : 0,11 mm Protective index : Full contact Manufacturer : KCL 741 Dermatril® L Material : Nitrile rubber Break through time : 480 min Glove thickness : 0,11 mm Protective index : Splash contact Manufacturer : KCL 741 Dermatril® L Remarks : This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D- 36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter : Filter type P1 type: The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature) .
The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.
No data available
no information available
Strong oxidizing agents
For Hazardous combustion products in the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide?
The signal word is no signal word.
What is the physical form of 2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide?
2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide is a solid with no data available color. It has no data available odor.
What is 2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide used for?
Laboratory chemicals, Manufacture of substances
What is the melting point of 2-[4-(Dimethylamino)styryl]-1-ethylpyridinium iodide?
The melting point is 267 °C Method: dec. and the boiling point is No data available.