Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- FiberLean Slurry
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Paper and board
Manufacturers & Suppliers
FiberLean Technologies Ltd
manufacturer
Par Moor Centre, Par Moor Road, Par, Cornwall, England, PL24 2SQ
+44 (0)1726 818 000
Emergency Contacts
CHEMTREC
+1 703 527 3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Pulp, Cellulose EC: 265-995-8 | 65996-61-4 | 95% | No |
| 2,2-dibromo-3-nitrilopropionamide EC: 233-539-7 | 10222-01-2 | 0.03% | Yes |
| 5-Chloro-2-methyl-1,2-thiazol-3(2H)-one (CIT) and 2-Methyl-1,2-thiazol-3(2H)-one (MIT) | 55965-84-9 | 0.0025% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move affected person to fresh air and keep warm and at rest in a position comfortable for breathing.
Wash skin thoroughly with soap and water. Use suitable lotion to moisturise skin.
Symptoms: May cause skin sensitisation or allergic reactions in sensitive individuals.
Do not rub eye. Rinse with copious quantities of water.
Rinse mouth thoroughly with water.
Immediate Medical Attention
Get medical attention if any discomfort continues (inhalation, ingestion). Seek medical attention if irritation persists (eye contact).
Medical Treatment
No specific recommendations.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
This product is non-combustible. No specific extinguishing media is needed.
Thermal decomposition or combustion products may include the following substances: Irritating gases or vapours. Carbon monoxide (CO). Nitrous gases (NOx). Hydrogen bromide (HBr). Hydrogen chloride (HCl).
Firefighter Protection
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
In case of spills, beware of slippery floors and surfaces.
Do not discharge into drains or watercourses or onto the ground.
Remove spillage with vacuum cleaner or collect with a shovel and broom, or similar. Collect and place in suitable waste disposal containers and seal securely. Flush contaminated area with plenty of water.
Materials: suitable waste disposal containers
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not eat, drink and smoke in work areas; wash hands after use; remove contaminated clothing and protective equipment before entering eating areas.
Store in a dry covered area.
Do not eat, drink and smoke in work areas; wash hands after use; remove contaminated clothing and protective equipment before entering eating areas.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Minimise airborne dust generation. Use process enclosures, local exhaust ventilation or other engineering controls to keep airborne levels below specified exposure limits. If user operations generate dust, fumes or mist, use ventilation to keep exposure to airborne particles below the exposure limit. Apply organisational measures, e.g. by isolating personnel from dusty areas. Remove and wash soiled clothing. Provide adequate ventilation. Avoid inhalation of vapours. Observe any occupational exposure limits for the product or ingredients.
Chemical-resistant, impervious gloves complying with an approved standard should be worn if a risk assessment indicates skin contact is possible. It is recommended that gloves are made of the following material: Nitrile rubber.
Eyewear complying with an approved standard should be worn if a risk assessment indicates eye contact is possible. The following protection should be worn: Chemical splash goggles or face shield. Contact lenses should not be worn when working with this product.
Local ventilation to control airborne dust levels below occupational exposure limits is recommended. In case of exposure, where engineering controls are insufficient, the use of Respiratory Protective Equipment (RPE) is recommended. A risk assessment process must be followed to ensure adequate protection from the airborne dust. The type of RPE must suit the work situation and the specific requirements of the wearer. Other environmental conditions should also be considered. The minimum “Assigned Protection Factor” (APF) required will depend on the measured or predicted occupational exposure levels divided by the OEL detailed in section 8.1. Filters specified as FFP2 and P2 have an APF of 10. Correctly fitted, these would reduce the exposure to the wearer down to one tenth of the working atmosphere. Depending on the assessment of the exposure, a lesser or higher efficiency of filter may be required. The manufacturer’s instructions and regulatory guidance regarding duration of use and correct fitting should be followed. The wearer of the selected RPE should receive training before use.
Wear apron or protective clothing in case of contact.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal ambient temperatures and when used as recommended.
There are no known reactivity hazards associated with this product.
Not applicable.
Avoid heat. Avoid freezing.
No specific material or group of materials is likely to react with the product to produce a hazardous situation.
Thermal decomposition or combustion products may include the following substances: Irritating gases or vapours. Carbon monoxide (CO). Nitrous gases (NOx). Hydrogen bromide (HBr). Hydrogen chloride (HCl).
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1. Toxicity
12.1. Toxicity
12.1. Toxicity
12.1 Toxicity
12.2. Persistence and degradability
The product is expected to be slowly biodegradable.
12.2. Persistence and degradability
12.2. Persistence and degradability
12.3. Bioaccumulative potential
The product does not contain any substances expected to be bioaccumulating.
12.3. Bioaccumulative potential
The product is not bioaccumulating.
12.3. Bioaccumulative potential
The product is not bioaccumulating.
12.4. Mobility in soil
12.5. Results of PBT and vPvB assessment
The substance is not classified as PBT or vPvB according to current EU criteria.
Results of PBT and vPvB assessment
Other adverse effects
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Recycling and disposal of packaging should be carried out by an authorised waste management company.
Where possible, recycling is preferable to disposal. Can be disposed of in compliance with local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Exempted in accordance with REACH Annex V.7
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for FiberLean Slurry?
The signal word is warning.
What is the physical form of FiberLean Slurry?
FiberLean Slurry is a slurry appearing as slurry with white/off-white. color. It has slight pungent. odor.
What is the solubility of FiberLean Slurry?
Insoluble in water.
What is FiberLean Slurry used for?
Paper and board
What are the hazard statements for FiberLean Slurry?
This substance has 1 hazard statement:
- H317: May cause an allergic skin reaction.