NextSDS Logo
Safety Data Sheet EN

LUBRIZOL® MF9141A

Keep this SDS organized and up to date

Add this SDS to your NextSDS library and keep all its safety information in one place.

Add to my SDS library for free
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LUBRIZOL® MF9141A

Regulatory Identifiers

CAS Number
N/A
UFI Code
84JF-43K3-G00P-YXJ5

Identified Uses

Miscellaneous fuel additive

Uses advised against

None identified.

Manufacturers & Suppliers

LUBRIZOL FRANCE logo

LUBRIZOL FRANCE

manufacturer

25 QUAI DE FRANCE CS 61062 76173 ROUEN CEDEX, 76173 FR

(33) 02.35.58.14.00

http://www.mylubrizol.com

Emergency Contacts

CHEMTREC

(+1) 703 527 3887

Emergency Contact

09.75.18.14.07

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2 H319
Carc. Cat. 2 H351
STOT SE Cat. 3 H335
Asp. Tox. Cat. 1 H304
Aquatic Chronic Cat. 2 H411

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

GHS09 - Environmental hazard

GHS09

Hazard Statements

H304 May be fatal if swallowed and enters airways.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.
H336 May cause drowsiness or dizziness.
H351 Suspected of causing cancer.
H411 Toxic to aquatic life with long lasting effects.

Precautionary Statements

P201 Obtain special instructions before use.
P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 Wash face, hands and any exposed skin thoroughly after handling.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P301 + P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor.
P302 + P352 IF ON SKIN: Wash with plenty of water.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical advice/attention.
P312 Call a POISON CENTER or doctor/ physician if you feel unwell.
P331 Do NOT induce vomiting.
P337 + P313 If eye irritation persists: Get medical advice/attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P391 Collect spillage.

Still copying SDS data manually?Free

You don't have to. NextSDS reads this SDS and adds the information to your library automatically.

Let NextSDS do it for me
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Hydrocarbons, C10, aromatics, greater than 1% naphthalene EC: 919-284-0 --- 25 - 50% Yes
2-Ethylhexan-1-ol EC: 203-234-3 --- 20 - 50% Yes
Hydrocarbons, C10, aromatics, less than 1% naphthalene EC: 918-811-1 --- 1 - 2.5% Yes
Phenol, 2-(2-propenyl)- EC: 217-119-0 --- 0.1 - 1% Yes
Benzene, 1,2,4-trimethyl- EC: 202-436-9 --- 5 - 10% Yes
Naphthalene EC: 202-049-5 --- 2.5 - 5% Yes
1,3,5-trimethylbenzene EC: 203-604-4 --- 1 - 2.5% Yes
1,2,3-Trimethylbenzene EC: 208-394-8 --- 1 - 5% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/ physician if you feel unwell.

Skin contact

Take off contaminated clothing and wash before re-use. Wash skin thoroughly with soap and water. Wash with soap and water. If skin irritation occurs, get medical attention. Get medical attention if symptoms occur. Launder contaminated clothing before reuse.

Eye contact

Rinse cautiously with water for several minutes. Flush thoroughly with water. If irritation occurs, get medical assistance. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.

Ingestion

Do NOT induce vomiting. If vomiting occurs naturally, the casualty should lean forward to reduce the risk of aspiration. Rinse mouth. Immediately call a POISON CENTER or doctor/ physician. Call a POISON CENTER or doctor/ physician if you feel unwell. Get medical attention if symptoms occur.

Symptoms: Aspiration of material due to vomiting can cause chemical pneumonitis which can be fatal.

Immediate Medical Attention

Immediately call a POISON CENTER or doctor/ physician.

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

CO2, Dry chemical or Foam. Water can be used to cool and protect exposed material.

Unsuitable media

Do not use water jet as an extinguisher, as this will spread the fire.

Specific hazards

Vapors may cause a flash fire or ignite explosively. Prevent buildup of vapors or gases to explosive concentrations. Vapors may travel considerable distance to a source of ignition and flash back. Container may rupture on heating. Material creates a special hazard because it floats on water. See section 10 for additional information.

Instructions

No data available.

Firefighter Protection

Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Ventilate closed spaces before entering them. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Keep upwind. Keep unauthorized personnel away.

Large spill

Dike far ahead of larger spill for later recovery and disposal.

Environmental

Avoid release to the environment. Prevent further leakage or spillage if safe to do so.

Cleanup methods

Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.

Materials: inert material

—

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Do not handle until all safety precautions have been read and understood. Obtain special instructions before use. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid breathing dust/fume/gas/mist/vapors/spray. Avoid contact with skin. Avoid contact with eyes. Observe good industrial hygiene practices. Use only in well-ventilated areas. Provide adequate ventilation. Use personal protective equipment as required. Wash hands thoroughly after handling. Launder contaminated clothing before reuse. Avoid environmental contamination.

Storage

Store in containers made of same material as original container. Keep cool. Store in a well-ventilated place. Store away from incompatible materials. See section 10 for incompatible materials. Do not store near potential sources of ignition.

Hygiene

Observe good industrial hygiene practices. Wash hands thoroughly after handling. Launder contaminated clothing before reuse.

Fire prevention

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Material should be handled in enclosed vessels and equipment, in which case general (mechanical) room ventilation should be sufficient. Local exhaust ventilation should be used at points where dust, mist, vapors or gases can escape into the room air. Mechanical ventilation or local exhaust ventilation is required. Adequate ventilation should be provided so that exposure limits are not exceeded.

Hands

Use nitrile or neoprene gloves. Use good industrial hygiene practices. In case of skin contact, wash hands and arms with soap and water. Polyvinyl alcohol. Note: polyvinyl alcohol gloves are water soluble and should not be used when there is potential for water contact. Polyvinyl chloride (PVC). Viton. Butyl rubber. Chemical resistant gloves. For typical use and handling of chemical substances, gloves should meet the standards set out in EN 374. For applications involving mechanical risks with potential for abrasion or puncture, the standards set out in EN 388 should be considered. For continuous contact, we suggest gloves with a minimum breakthrough time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. For general applications, we recommend gloves with a thickness typically greater than 0.35 mm. Thinner gloves (down to 0.1 mm or less) may be required where a high degree of manual dexterity is needed. Thicker gloves (up to 3 mm or more) may be required where there is a mechanical (as well as a chemical) risk.

Eyes

Wear tight-fitting goggles or face shield. Safety glasses. If potential for splash or mist exists, wear chemical goggles or faceshield. Eye protection should meet the standards set out in EN 166.

Respiratory

A respiratory protection program compliant with all applicable regulations must be followed whenever workplace conditions require the use of a respirator. Use respirator with an organic vapor and dust/mist cartridge if the recommended exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites. Respiratory Protective Equipment (RPE) is not normally required where there is adequate natural or local exhaust ventilation to control exposure. In case of insufficient ventilation, wear suitable respiratory equipment.

Skin/Body

Wear apron or protective clothing in case of contact. Do not wear rings, watches or similar apparel that could entrap the material. Gloves, coveralls, apron, boots as necessary to minimize contact.

Environmental

No data available. See section 6 for details.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Dark amber
Colour Intensity
---
Form
liquid
Odor
Characteristic
Odor Threshold
No data available.
Ph
Not applicable
Melting Point
---
Boiling Point
No data available.
Flash Point
62 °C (Pensky-Martens Closed Cup)
Freezing Point
No data available.
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
No data available.
Vapor Pressure
No data available.
Vapor Density
---
Relative Density
0.9 (15.6 °C)
Bulk Density
---
Density
---
Flammability
No data available.
Upper Explosive Limit
No data available.
Lower Explosive Limit
No data available.
Explosive Limits
---
Auto Ignition Temperature
No data available.
Decomposition Temperature
No data available.
Solubility
---
Partition Coefficient
No data available.
Solubility In Water
Insoluble in water
Solubility In Fat
---
Molecular Weight
---
Voc Content
No data available.
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
7.4 mm2/s (40 °C)
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Material is stable under normal conditions.

Reactivity

No data available.

Hazardous reactions

Will not occur.

Avoid

Heat, sparks, flames, Excessive heat

Incompatible

Strong caustic agents, Contact with acids

Decomposition

Thermal decomposition or combustion may generate smoke, carbon monoxide, carbon dioxide, and other products of incomplete combustion.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

12.1 Ecotoxicity

Hydrocarbons, C10, aromatics, greater than 1% naphthalene LC 50 (Rainbow Trout, 4 Days): 2 mg/l

12.1 Ecotoxicity

Fish 2-Ethylhexan-1-ol LC 50 (Fathead Minnow, 4 d): 28.2 mg/l LC 50 (Golden Orfe, 4 d): 17.1 mg/l

12.1 Ecotoxicity

Fish ++ Benzene, 1,2,4-trimethyl- LC 50 (Fathead Minnow, 4 Days): 7.72 mg/l

12.1 Ecotoxicity

Hydrocarbons, C10, aromatics, less than 1% naphthalene LC 50 (Rainbow Trout, 96 h): 2 mg/l

12.1 Ecotoxicity

Aquatic Invertebrates Hydrocarbons, C10, aromatics, greater than 1% naphthalene EC 50 (Water flea (Daphnia magna), 2 d): 3 mg/l

12.1 Ecotoxicity

Aquatic Invertebrates 2-Ethylhexan-1-ol EC 50 (Water flea (Daphnia magna), 2 d): 39 mg/l

12.1 Ecotoxicity

Aquatic Invertebrates ++ Benzene, 1,2,4-trimethyl- EC 50 (Water flea (Daphnia magna), 2 d): 3.6 mg/l

12.1 Ecotoxicity

Aquatic Invertebrates ++ 1,3,5-trimethylbenzene EC 50 (Water flea (Daphnia magna), 2 d): 6 mg/l

12.1 Ecotoxicity

Hydrocarbons, C10, aromatics, less than 1% naphthalene EC 50 (Water flea (Daphnia magna), 48 h): 10 mg/l

12.1 Toxicity

Hydrocarbons, C10, aromatics, greater than 1% naphthalene EC 50 (Green algae (Selenastrum capricornutum), 4 d): 1.1 mg/l

Toxicity to Aquatic Plants

2-Ethylhexan-1-ol EC 50 (Green algae (Scenedesmus quadricauda), 3 d): 16.6 mg/l

12.1 Toxicity

++ 1,3,5-trimethylbenzene EC 50 (Green algae (Scenedesmus quadricauda), 2 Days): 25 mg/l

Toxicity

Hydrocarbons, C10, aromatics, less than 1% naphthalene EC 50 (Algae (Pseudokirchneriella subcapitata), 72 h): > 1 mg/l NOEC (Algae (Pseudokirchneriella subcapitata), 72 h): 1 mg/l

Toxicity

2-Ethylhexan-1-ol EC 50 (Pseudomonas putida, 0.1 d): 540 mg/l EC 50 (Sludge, 0.5 d): > 100 mg/l

12.2 Persistence and Degradability

Hydrocarbons, C10, aromatics, greater than 1% naphthalene OECD TG 301 F, 58 %, 28 d, Not readily degradable.

12.2 Persistence and Degradability

Biodegradation 2-Ethylhexan-1-ol OECD TG 302 B, 95 %, 5 d, Readily biodegradable OECD TG 301 C, 100 %, 14 d, Readily biodegradable

12.2 Persistence and Degradability

### Biodegradation Hydrocarbons, C10, aromatics, less than 1% naphthalene OECD TG 301 F, 49.56 %, 28 d, Not readily degradable.

12.3 Bioaccumulative potential

Bioconcentration Factor (BCF)

12.3 Bioaccumulative potential

Bioconcentration Factor (BCF) 2-Ethylhexan-1-ol Bioconcentration Factor (BCF): 25.35 (calculated)

12.3 Bioaccumulative potential

Partition Coefficient n-octanol / water (log Kow) 2-Ethylhexan-1-ol Log Kow: 2.9 (Measured)

12.3 Bioaccumulative potential

Partition Coefficient n-octanol / water (log Kow) ++ Benzene, 1,2,4-trimethyl- Log Kow: 3.63 (calculated)

12.4 Mobility:

2-Ethylhexan-1-ol soil - 1.42

12.5 Results of PBT and vPvB assessment

No data available

No data available

12.6 Endocrine Disruption:

Product: The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.

The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.

12.7 Other adverse effects

Product: Toxic to aquatic life with long lasting effects.

The product is classified as toxic to aquatic life with long lasting effects.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations.

Disposal

Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3082
Shipping Name
ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Naphthalene, Petroleum naphtha)
Transport Class
9
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

Regulatory information for LUBRIZOL® MF9141A, including EU regulatory compliance and global inventory status.

Chemical Safety Assessment Not performed
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LUBRIZOL® MF9141A?

The signal word is danger.

What is the physical form of LUBRIZOL® MF9141A?

LUBRIZOL® MF9141A is a liquid with dark amber color. It has characteristic odor.

What is LUBRIZOL® MF9141A used for?

Miscellaneous fuel additive

What are the hazard statements for LUBRIZOL® MF9141A?

This substance has 7 hazard statements:

  • H304: May be fatal if swallowed and enters airways.
  • H315: Causes skin irritation.
  • H319: Causes serious eye irritation.
  • H335: May cause respiratory irritation.
  • H336: May cause drowsiness or dizziness.
  • H351: Suspected of causing cancer.
  • H411: Toxic to aquatic life with long lasting effects.