Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Compatherm 1p Filler
- Product Code
- Nolato 92XX series where XX is a number between 00 and 99.
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Industrial purposes
Uses advised against
None known.
Manufacturers & Suppliers
Nolato Silikonteknik AB
manufacturer
P.O. Box 62, 694 22 Hallsberg, Sweden
+46 582 88900
http://www.nolato.com
Emergency Contacts
The National Poisons Information Service
111
24 h service
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS09
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Aluminium oxide | 1344-28-1 | 95% | No |
| Zinc oxide EC: 215-222-5 | 1314-13-2 | 15% | Yes |
| Silicone rubber | 63394-02-5 | 15% | No |
| Aluminium nitride | 24304-00-5 | 40% | No |
| Boron nitride | 10043-11-5 | 15% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Upon breathing difficulties or irritation of the respiratory tract: Bring the person into fresh air and stay with him/her.
Upon irritation: rinse with water. In the event of continued irritation, seek medical assistance.
Upon irritation of the eye: Remove contact lenses and open eyes widely. Flush eyes with water or saline water (20-30 °C) for at least 5 minutes. Seek medical assistance and continue flushing during transport.
If the person is conscious, rinse the mouth with water and stay with the person. Never give the person anything to drink. In case of malaise, seek medical advice immediately and bring the safety data sheet or label from the product. Do not induce vomiting, unless recommended by the doctor. Have the person lean forward with head down to avoid inhalation of or choking on vomited material.
Immediate Medical Attention
None known.
Medical Treatment
Bring this safety data sheet or the label from this product.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Alcohol-resistant foam, carbon dioxide, powder, water mist.
Waterjets should not be used, since they can spread the fire.
Fire will result in dense smoke. Exposure to combustion products may harm your health.
Closed containers, which are exposed to fire, should be cooled with water.
Firefighter Protection
Wear self-contained breathing apparatus and protective clothing to prevent contact. Upon direct exposure contact The National Poisons Information Service (dial 111, 24 h service) in order to obtain further advice.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
No specific requirements.
Avoid discharge to lakes, streams, sewers, etc.
cleaning should be performed with normal cleaning agents. Avoid use of solvents.
Related Products
Similar products with comparable safety profiles
DAP All Purpose Adhesive & Filler Part A Resin
---
Gyproc JointFiller 45
---
FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS
CAS: mixture of 436083-99-7
Premium Wood Filler
---
DELETE Pattex Crack Filler 290g
---
DAP All Purpose Adhesive & Filler Part B Hardener
---
Plastic Wood Solvent Wood Filler
---
Plastic Wood Epoxy Filler Part B Hardener
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Smoking, drinking and consumption of food is not allowed in the work area.
No specific requirements
Smoking, drinking and consumption of food is not allowed in the work area.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The formation of vapours must be kept at a minimum and below current limit values (see above). Installation of a local exhaust system if normal air flow in the work room is not sufficient is recommended. Ensure eyewash and emergency showers are clearly marked.
Compathem 1p Filler. Butyl: 0,3 mm thickness, > 480 min breakthrough time, Standards: EN374-2, EN374-3, EN388. Nitrile: 0.1 mm thickness, Standards: EN374-2.
No specific requirements.
No specific requirements.
No specific requirements.
Keep damming materials near the workplace. If possible, collect spillage during work.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable under the conditions, noted in section 7 "Handling and storage".
No data available.
None known.
None known.
Strong acids, strong bases, strong oxidizing agents, and strong reducing agents.
The product is not degraded when used as specified in section 1.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1. Toxicity
12.2. Persistence and degradability
No data available.
12.3. Bioaccumulative potential
No data available.
12.4. Mobility in soil
12.5. Results of PBT and vPvB assessment
The mixture does not contain any substances considered to meet the criteria classifying them as PBT and/or vPvB.
12.6. Endocrine disrupting properties
The substance is not considered to have endocrine disrupting properties.
12.7. Other adverse effects
The product contains substances toxic to the environment and may cause long-term adverse effects to the aquatic environment.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of contents/container to an approved waste disposal plant.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Zinc oxide)
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Not applicable.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Compatherm 1p Filler?
The signal word is no signal word.
What is the physical form of Compatherm 1p Filler?
Compatherm 1p Filler is a paste with various colours color. It has testing not relevant or not possible due to the nature of the product. odor.
What is Compatherm 1p Filler used for?
Industrial purposes
What are the hazard statements for Compatherm 1p Filler?
This substance has 1 hazard statement:
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of Compatherm 1p Filler?
The melting point is Testing not relevant or not possible due to the nature of the product. and the boiling point is Testing not relevant or not possible due to the nature of the product..