Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS
- Product Form
- fibrous mastic
- Chemical Name
- mixture of 436083-99-7 biosoluble flock (marking Thermal C.) Colloidal Silica
Regulatory Identifiers
- CAS Number
- mixture of 436083-99-7 Check regulations →
Identified Uses
High density biosoluble fibrous mastic for elevated temperatures, useful for grouting or gluing on refractory products in general, such as: refractory bricks (dense and/or insulating); cavities created between the carpentry and the insulation of thermal plants (industrial furnaces, boilers, etc.). Specific for repairing industrial heating systems (furnaces, boilers, etc.) with conduction at maximum temperatures of 1100°C for PLUS and 1200°C for HT
Manufacturers & Suppliers
SIM s.r.l. Socio unico
manufacturer
Via IV Novembre 42 – 20012 Cuggiono (MI)
+39 02.97.25.03.29
http://www.sim-cdm.it
REFRATTARI GENERALI S.r.l.
distributor
Via Giovanni XXIII 19 – 20014 Nerviano (MI), Italy
+39/0331/58.56.82
Emergency Contacts
SIM s.r.l. Socio unico
+39 / 02 / 97.25.03.29
Emergency telephone number (Italy)
118
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Typical chemical composition: biosoluble flock, marking Thermal Ceramics (Cas.436083-99-7) colloidal silica (Cas. n. EEC n. non-dangerous) disinfectant, water.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| biosoluble flock | --- | --- | No |
| marking Thermal Ceramics | 436083-99-7 | --- | No |
| colloidal silica | --- | --- | No |
| disinfectant | --- | --- | No |
| water | --- | --- | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
take the person outdoors, give water to drink to clear the throat and let blow the nose.
rinse the affected areas with soap and water thoroughly. Do not use detergents.
rinse thoroughly with water and have a special eye drops available. Don't rub your eyes.
drink plenty of water.
Immediate Medical Attention
If possible, show this Safety Data Sheet to the doctor in attendance.
Medical Treatment
Special treatment (see section 4.2).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The material in question is not flammable and is not a comburent compound. For this reason, fire safety measures are not applicable.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
In the event of accidental leaks, keep to a minimum and avoid raising the dust. Bring the situation back to normal as soon as possible.
The product does not cause and cannot be implicated in causes of environmental damage
collect mechanically
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The product is not explosive, it is not combustible, it is not oxidising.
Store in a dry place and in the original packaging and away from heat or sunlight.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Wear industrial leather gloves
As necessary, wear goggles or safety glasses with side shields.
For dust concentrations below the applicable exposure limit value, RPE is not required but FFP2 respirators should be provided for use on a voluntary basis. For short term operations where excursions are less than ten times the applicable limit value, use FFP2 respirators. In case of higher concentrations or where the concentration is not known, please contact our company and/or your supplier REFRA TTARI GENERALI (manufactured by SIM S.r.l.).
work clothes, which are loose fitting at the neck and wrists. Soiled clothes should be cleaned to remove excess dust before being taken off (e.g. use vacuum cleaner, not compressed air).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable product
Stable at room temperature in a dry place. After a long period of use at temperatures above 900°C, this amorphous material begins to transform into a mixture of different crystalline phases.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Waste / residue from these materials can generally be sent to landfills authorized for this purpose.
In order to know which group the material belongs to, consult the European list (Decision n°2000/532 / CE amended) and verify that it complies with the regional and national regulations. In the event that these wastes / residues have been polluted by hazardous materials, specific recommendations should be applied.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Fibres contained in this product are free of any classification and do not require labelling under CLP regulation. Under criteria listed in nota Q of Directive 67/548/EEC and Annex VI of regulation (EC) 1272/2008, fibres are exonerated from carcinogen classification.
Labelling according to EC regulation 1272/2008 and amending EU 944/2013.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS?
The signal word is no signal word.
What is the physical form of FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS?
FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS is a light gray paste appearing as light gray paste with white / very light gray color. It has odourless odor.
What is the solubility of FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS?
Less than 1 mg/l
What is FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS used for?
High density biosoluble fibrous mastic for elevated temperatures, useful for grouting or gluing on refractory products in general, such as: refractory bricks (dense and/or insulating); cavities created between the carpentry and the insulation of thermal plants (industrial furnaces, boilers, etc.). Specific for repairing industrial heating systems (furnaces, boilers, etc.) with conduction at maximum temperatures of 1100°C for PLUS and 1200°C for HT
What is the melting point of FIBROUS MASTIC FILL BIO SW 607 HT and FILL BIO SW PLUS?
The melting point is SW PLUS > 1200°C / SW 607 HT > 1300 °C and the boiling point is Not applicable.