Dimethyl sulfoxide

After inhalation: fresh air.

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.

After eye contact: rinse out with plenty of water. Remove contact lenses.

After swallowing: make victim drink water (two glasses at most).

Water, Foam, Carbon dioxide (CO2), Dry powder

For this substance/mixture no limitations of extinguishing agents are given.

Combustible. Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating. Development of hazardous combustion gases or vapours possible in the event of fire.

Remove container from danger zone and cool with water. Suppress (knock down) gases/vapors/mists with a water spray jet.

Do not breathe vapors, aerosols. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert.

Do not let product enter drains.

Take up with liquid-absorbent material (e.g. Chemizorb®). Clean up affected area.

Materials: liquid-absorbent material (e.g. Chemizorb®)

Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharge. Change contaminated clothing. Wash hands after working with substance.

Tightly closed. Store under inert gas. hygroscopic

Change contaminated clothing. Wash hands after working with substance.

Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharge.

Full contact: Material: Chloroprene, Minimum layer thickness: 0,65 mm, Break through time: 480 min, Material tested: KCL 720 Camapren®. Splash contact: Material: Latex gloves, Minimum layer thickness: 0,6 mm, Break through time: 240 min, Material tested: Lapren® (KCL 706 / Aldrich Z677558, Size M).

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

Recommended Filter type: Filter A (acc. to DIN 3181) for vapours of organic compounds. The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Do not let product enter drains.

The product is chemically stable under standard ambient conditions (room temperature).

Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical.

Risk of explosion with: acetylcholine, organic halides, perchlorates, Acid chlorides, nonmetallic halides, iron(III) compounds, nitrates, fluorides, chlorates, hydrides, perchloric acid, Oxides of phosphorus, Nitric acid, silver compounds, silicon compounds, silanes, acid halides. Exothermic reaction with: boron compounds, oxyhalogenic compounds, Potassium, sodium, Strong oxidizing agents, phosphorus halides, strong reducing agents, Acid chlorides, Strong acids, silver salt, nitrogen dioxide. Risk of ignition or formation of inflammable gases or vapours with: potassium permanganate

Strong heating.

acetylcholine, organic halides, perchlorates, Acid chlorides, nonmetallic halides, iron(III) compounds, nitrates, fluorides, chlorates, hydrides, perchloric acid, Oxides of phosphorus, Nitric acid, silver compounds, silicon compounds, silanes, acid halides, boron compounds, oxyhalogenic compounds, Potassium, sodium, Strong oxidizing agents, phosphorus halides, strong reducing agents, Strong acids, silver salt, nitrogen dioxide, potassium permanganate

In the event of fire: see section 5

No data available