Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- SYLFAT™ 2LT
- Product Code
- 200000000255
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Industrial uses: Uses of substances as such or in preparations at industrial sites. Formulation [mixing] of preparations and/or re-packaging (excluding alloys).
Uses advised against
None known.
Manufacturers & Suppliers
Kraton Chemical, LLC
manufacturer
P.O. Box 550850, Jacksonville, FL 32255-0850
904-928-8700
Emergency Contacts
CHEMTREC
800-424-9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Tall Oil Fatty Acids | 61790-12-3 | 100% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air.
Wash off with soap and water.
Rinse with water.
Symptoms: Direct contact with eyes may cause temporary irritation.
Rinse mouth.
Immediate Medical Attention
Call a physician if symptoms develop or persist (inhalation). Get medical attention if irritation develops and persists (skin/eye). Get medical attention if symptoms occur (ingestion).
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
During fire, gases hazardous to health may be formed.
Wear suitable protective equipment. Move containers from fire area if you can do so without risk.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary personnel away. For personal protection, see section 8 of the SDS.
Absorb in vermiculite, dry sand or earth and place into containers. Clean surface thoroughly to remove residual contamination.
Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Use a non-combustible material like vermiculite, sand or earth to soak up the product and place into a container for later disposal. Prevent entry into waterways, sewer, basements or confined areas. Following product recovery, flush area with water.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS. Avoid discharge into drains, water courses or onto the ground.
Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Clean surface thoroughly to remove residual contamination.
Materials: vermiculite, dry sand or earth
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Porous material such as rags, paper, insulation, or organic clay may spontaneously combust when wetted with this material. May auto-oxidize with sufficient heat generation to ignite if spread (as a thin film) or absorbed on porous or fibrous material. Contaminated rags and cloths must be put in fireproof containers for disposal. Avoid prolonged exposure. Avoid release to the environment. Observe good industrial hygiene practices. Follow all SDS/label precautions even after container is emptied because they may retain product residues.
Do not store in direct sunlight. Store in original tightly closed container. Keep containers closed when not in use. Store at ambient temperature and atmospheric pressure. Store away from incompatible materials (see Section 10 of the SDS).
Observe good industrial hygiene practices.
Porous material such as rags, paper, insulation, or organic clay may spontaneously combust when wetted with this material. May auto-oxidize with sufficient heat generation to ignite if spread (as a thin film) or absorbed on porous or fibrous material. Contaminated rags and cloths must be put in fireproof containers for disposal.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Material is stable under normal conditions.
The product is stable and non-reactive under normal conditions of use, storage and transport.
No dangerous reaction known under conditions of normal use.
Strong oxidizing agents. Avoid temperatures exceeding the flash point. Contact with incompatible materials. Porous material such as rags, paper, insulation, or organic clay may spontaneously combust when wetted with this material.
Strong oxidizing agents.
Upon decomposition this product emits acrid dense smoke with carbon dioxide, carbon monoxide, water and other products of combustion.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
Persistence and degradability
The product is biodegradable.
12.2 Persistence and degradability
Bioaccumulative potential
Mobility in soil
Other adverse effects
No other adverse environmental effects are expected from this component.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of in accordance with local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for SYLFAT™ 2LT?
The signal word is no signal word.
What is the physical form of SYLFAT™ 2LT?
SYLFAT™ 2LT is a liquid. appearing as liquid. with yellow. color. It has mild. odor.
What is SYLFAT™ 2LT used for?
Industrial uses: Uses of substances as such or in preparations at industrial sites. Formulation [mixing] of preparations and/or re-packaging (excluding alloys).
What are the hazard statements for SYLFAT™ 2LT?
This substance has 1 hazard statement:
- The substance does not meet the criteria for classification.
What is the melting point of SYLFAT™ 2LT?
The melting point is Not available. and the boiling point is >392 °F (>200 °C).