HI EP SEALER PART B

Move to fresh air. Give oxygen or artificial respiration if needed. When risk of unconsciousness, place and transport the victim in secured recovery position. Provide fresh air, rest and warmth. Call a physician immediately.

Symptoms: Harmful by inhalation.

Use a mild soap if available. Wash off immediately with soap and plenty of water while removing all contaminated clothes and shoes. If skin irritation persists, call a physician. Do not use solvent or thinners to clean skin.

Symptoms: Irritating to skin. May cause sensitization by skin contact.

Immediate medical attention is required. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses.

Symptoms: Causes serious eye damage.

Do not induce vomiting. Get immediate medical attention. Never give anything by mouth to an unconscious person. If vomiting occurs spontaneously: Keep head below hips to prevent aspiration of stomach vomit into lungs. Provide fresh air, rest and warmth.

Symptoms: Harmful if swallowed.

Carbon Dioxide, Dry Chemical, Foam

Alcohol, Alcohol based solutions, any other media not listed above. Do not use a solid water stream as it may scatter and spread fire.

Use of water may produce very toxic aquatic solutions.

Keep containers and surroundings cool with water spray.

Ensure adequate ventilation. Use personal protective equipment. Remove all sources of ignition.

Do not allow material to contaminate ground water system. Prevent product from entering drains.

soak up with non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and transfer to a container for disposal according to local / national regulations (see section 13). Clean with detergents. Avoid solvents.

Materials: non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite), detergents

Wear personal protective equipment. Open drum carefully as content may be under pressure. Do not breathe vapours or spray mist. Persons with a history of skin sensitisation problems or asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this preparation is being used.

Store in original container. Keep locked up or in an area accessible only to qualified or authorised persons. Keep container closed. Store in a dry, well ventilated place away from sources of heat, ignition and direct sunlight. Store in upright position only. Storage of corrosive material.

Wash hands before breaks and at the end of workday. When using, do not eat, drink or smoke.

Prevent the creation of flammable or explosive concentrations of vapour in air. Electrical equipment should be protected to the appropriate standard.

Ensure adequate ventilation, especially in confined areas.

Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact). Be aware that in daily use the durability of a chemical resistant protective glove can be notably shorter than the break through time measured according to EN 374, due to the numerous outside influences (e.g. temperature). Use chemical resistant gloves and lotions and barrier creams to prevent drying of the skin. Protective gloves complying with EN 374: Butyl rubber. Nitril rubber. Recommended glove material for mixed product: Protective gloves complying with EN 374: Butyl rubber. Nitril rubber.

Safety glasses with side-shields conforming to EN166.

Wear respiratory protection with combination filter (dust and gas filter, EN 14387:2004 +A1:2008) during spraying operations: Gas filter type A2 (organic substances). Dust filter P3 (for fine dust). When working in confined or poorly ventilated spaces, a battery powered assisted air-fed mask must be used.

Long sleeved clothing. Remove and wash contaminated clothing before re-use.

Stable under recommended storage conditions.

No reactivity hazards known under recommended storage and use conditions.

No reactivity hazards known under recommended storage and use conditions.

Avoid heat, sparks, flames and other ignition sources.

strong oxidising agents and strongly acid or alkaline materials

Ammonia gas may be liberated at high temperatures. In case of fire or hot work operations, hazardous decomposition products may be formed such as: Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), aliphatic amines, aldehydes.

Dispose of waste material at an approved (hazardous) waste treatment/disposal facility in accordance with applicable local state, and federal regulations.

Dispose of waste material at an approved (hazardous) waste treatment/disposal facility in accordance with applicable local state, and federal regulations.