Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- UV SEALER 661-103-0000
- Product Code
- 661-103-0000
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coatings for industrial use
Manufacturers & Suppliers
Treffert Coatings GmbH
manufacturer
Am Kirchberg 1, 63754 Alzenau
Emergency Contacts
Treffert Coatings GmbH
+49 (0) 6023/961-0
Monday to Friday 8.00 to 16.00 o'clock
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Radiation-hardening preparations
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2,2-bis(acryloyloxymethyl)butyl acrylate EC: 239-701-3 | 15625-89-5 | 50 - 100% | Yes |
| Glycerol propoxy triacetate EC: 500-114-5 | 52408-84-1 | 12.5 - 20% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove casualty to fresh air and keep warm and at rest. In case of irregular breathing or respiratory arrest provide artificial respiration.
Remove contaminated, saturated clothing immediately. After contact with skin, wash immediately with plenty of water and soap. Do not use solvents or thinners. Conditions to avoid: UV-radiation/sunlight
Symptoms: Causes mild skin irritation.
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical advice immediately.
If swallowed, rinse mouth with water (only if the person is conscious). Seek medical advice immediately. Keep victim calm. Do NOT induce vomiting.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
alcohol resistant foam, carbon dioxide fire blanket, Powder, spray mist, (water)
strong water jet
Dense black smoke occurs during fire. Inhaling hazardous decomposing products can cause serious health damage.
Cool closed containers that are near the source of the fire.
Firefighter Protection
Provide a conveniently located respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep away from sources of ignition. Ventilate affected area. Do not breathe vapours.
Do not allow to enter into surface water or drains.
Clean using cleansing agents. Do not use solvents.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in well-ventilated areas. Keep away from heat sources, sparks and open flames. Avoid contact with skin, eyes and clothes. Do not inhale dusts, particulates and spray mist when using this preparation. Avoid respiration of swarf. When using do not eat, drink or smoke. Personal protection equipment: refer to chapter 8. Do not empty containers with pressure - no pressure vessel! Always keep in containers that correspond to the material of the original container. Follow the legal protection and safety regulations.
Store in a well-ventilated and dry room at temperatures between 5 °C and 30 °C. Protect from heat and direct sunlight. Keep container tightly closed. Store carefully closed containers upright to prevent any leaks. Keep only in the original container.
When using do not eat, drink or smoke.
Keep away from heat sources, sparks and open flames. Remove all sources of ignition. Smoking is forbidden.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide good ventilation. This can be achieved with local or room suction.
For prolonged or repeated handling the following glove material must be used: Nitrilkautschuk oder Butylkautschuk. Thickness of the glove material > 0,4 mm; Breakthrough time (maximum wearing time) > 480 min. Observe the instructions and details for use, storage, maintenance and replacement provided by the protective glove manufacturer. Penetration time of glove material depending on intensity and duration of exposure to skin. Recommended glove articles DIN EN 374
Wear closely fitting protective glasses in case of splashes.
If concentration of solvents is beyond the occupational exposure limit values, approved and suitable respiratory protection must be used. Observe the wear time limits according GefStoffV in combination with the rules for using respiratory protection apparatus (BGR 190). Use only respiratory protection equipment with CE-symbol including four digit test number.
Wear antistatic clothing of natural fibers (cotton) or heat resistant synthetic fibers.
Do not allow to enter into surface water or drains. See chapter 7. No additional measures necessary.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable when applying the recommended regulations for storage and handling. Further information on correct storage: refer to chapter 7.
Keep away from strong acids, strong bases and strong oxidizing agents to avoid exothermic reactions.
Heat, strong ultraviolet radiation. An exotherm polymerization of the product may thereby be caused. Avoid unintended contact with it. Hazardous decomposition byproducts may form with exposure to high temperatures.
Hazardous decomposition byproducts may form with exposure to high temperatures, e.g.: carbon dioxide, carbon monoxide, smoke, nitrogen oxides.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Do not allow to enter into surface water or drains. This material and its container must be disposed of in a safe way. Waste disposal according to directive 2008/98/EC, covering waste and dangerous waste.
Do not allow to enter into surface water or drains. This material and its container must be disposed of in a safe way.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- n.a.
- Shipping Name
- n.a.
- Transport Class
- n.a.
- Packing Group
- n.a.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Chemical safety assessments for substances in this preparation were not carried out.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for UV SEALER 661-103-0000?
The signal word is warning.
What is the physical form of UV SEALER 661-103-0000?
UV SEALER 661-103-0000 is a liquid appearing as liquid, colourless with colourless color. It has characteristic odor.
What is UV SEALER 661-103-0000 used for?
Coatings for industrial use
What are the hazard statements for UV SEALER 661-103-0000?
This substance has 3 hazard statements:
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.