Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CM 2K pre-fill HS topcoat
- Product Code
- 230677, 249457, 249464, 249471
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lacquer
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
MOTIP DUPLI GmbH
manufacturer
Kurt Vogelsang Strasse 6, D-74855 Haßmersheim
+49/6266/75-0
Emergency Contacts
Emergency Contact
+49 6266-75-310
Mo - Th 08:00 am - 04:00 pm, Fr 08:00 am - 00:30 pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| dimethyl ether EC: 204-065-8 | 115-10-6 | 50 - 75% | Yes |
| acetone EC: 200-662-2 | 67-64-1 | 12.5 - 20% | Yes |
| aliphatic polycyanate EC: 500-060-2 | 28182-81-2 | 5 - 10% | Yes |
| butanone EC: 201-159-0 | 78-93-3 | 2.5 - 5% | Yes |
| 2-methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 2.5 - 5% | Yes |
| n-butyl acetate EC: 204-658-1 | 123-86-4 | 2.5% | Yes |
| 3-isocyanatomethyl-3,5,5-trimethylcyclohexyl isocyanate, oligomers EC: 500-125-5 | 53880-05-0 | 2.5% | Yes |
| butan-1-ol EC: 200-751-6 | 71-36-3 | 2.5% | Yes |
| xylene EC: 905-588-0 | --- | 2.5% | Yes |
The content of Benzene (EINECS-Nr. 200-753-7) in the ingredients is less than 0,1% (Note P Annex 1A 1272/2008 EU), so the classification as carcinogen need not to apply. xylene: Contains ethylbenzene CAS 100-41-4
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Drink plenty of water and provide fresh air. Call for a doctor immediately.
Immediate Medical Attention
Call for a doctor immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
During heating or in case of fire poisonous gases are produced.
Firefighter Protection
Mouth respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Related Products
Similar products with comparable safety profiles
Aerosol 2K Fill In + 100ml Lack 2K BHS CAT Yellow
---
Aerosol 2K Fill In + 100ml Lack 2K BHS CAT BLACK
---
Colormatic 2K ClearCoat with hardener gloss / high gloss
---
Colormatic 2K ClearCoat with hardener gloss / high gloss
---
Construction Top Coat
---
MATTING AGENT HS CLEARCOATS
---
2C-PUR Topcoat MIO
---
Motip 2K Clear coat highgloss
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Keep respiratory protective device available.
Observe official regulations on storing packagings with pressurised containers. Keep container tightly sealed.
Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
In case of contact with spray dust protective gloves made of butyl shoud be used (min. 0.4 mm thick), e.g. KCL Camatril, article no. 898 or similar products Solvent resistant gloves Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Protective gloves The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation Material of gloves: Butyl rubber, BR The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: Butyl rubber gloves with a thickness of 0.4 mm are resistant to: Acetone: 480 min Butyl acetate: 60 min Ethyl acetate: 170 min Xylene: 42 min The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
Not necessary if room is well-ventilated. In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
12.6 Endocrine disrupting properties
12.7 Other adverse effects
12.1 Toxicity
12.1 Toxicity
12.1 Toxicity
12.1 Toxicity
12.1 Toxicity
12.2 Persistence and degradability
No further relevant information available.
12.3 Bioaccumulative potential
No further relevant information available.
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance is not considered to be persistent, bioaccumulative and toxic (PBT) or very persistent and very bioaccumulative (vPvB).
Other adverse effects
No further relevant information available.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Must not be disposed together with household garbage.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2
- Packing Group
- not regulated
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CM 2K pre-fill HS topcoat?
The signal word is danger.
What is the physical form of CM 2K pre-fill HS topcoat?
CM 2K pre-fill HS topcoat is a aerosol with according to product specification color. It has characteristic odor.
What is CM 2K pre-fill HS topcoat used for?
Lacquer
What are the hazard statements for CM 2K pre-fill HS topcoat?
This substance has 5 hazard statements:
- H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H332: Harmful if inhaled.
- H336: May cause drowsiness or dizziness.
What is the melting point of CM 2K pre-fill HS topcoat?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..