Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Construction Top Coat
- Product Code
- TP13-HP
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Nail art
Manufacturers & Suppliers
Foshan YouGel Cosmetics Co.,Ltd
manufacturer
Room 2723, Xinkai Plaza Building 2, Yongsheng West Rd 22, Guicheng Nanhai District, Foshan China
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with additions
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Pentaerythritol | 115-77-5 | 10 - 25% | No |
| Cellulose acetate butyrate | 9004-36-8 | 10 - 35% | No |
| ACRYLATES COPOLYMER | 25035-69-2 | 10 - 40% | No |
| BHT | 128-37-0 | 0.5 - 1% | No |
| TMO | 270586-78-2 | 3 - 10% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Wash with water and soap for a few minute.
Immediately flush eyes with plenty of water for a few minutes, occasionally lifting the upper and lower eyelids.
Gargle with water, and to drink enough water or milk to emetic. If symptoms persist consult doctor.
Immediate Medical Attention
Get medical aid immediately if eye symptoms can not be eased.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, sand, extinguishing powder
None.
Do not inhale explosion gases or combustion gases.
Firefighter Protection
Wear fully protective suit. Mouth respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Mix absorb leaked material with (sand, diatomite, sawdust) then Cleaning and placed into a suitable container handling, and scrub the area with towel and water.
Isolation accident area to prevent the leak products to be contaminated ,and then to recycling collection the leak products.
Do not allow much product to reach sewage system or any water course.
Mix absorb leaked material with (sand, diatomite, sawdust) then Cleaning and placed into a suitable container handling, and scrub the area with towel and water.
Materials: sand, diatomite, sawdust, towel and water
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in cool, dry place in tightly closed receptacles.
Store in a cool location. Keep container tightly sealed. Store in cool, dry conditions in well sealed receptacles.
Keep ignition sources away , Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The data for this section has not been processed yet.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable.
Hazardous polymerization will not occur.
The following combustion products may be generated: carbon dioxide, carbon monoxide, water vapor, and trace volatile organic compounds or other toxic gases / smoke.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Construction Top Coat?
The signal word is warning.
What is the physical form of Construction Top Coat?
Construction Top Coat is a viscous liquid with pale yellow color. It has slight irritating odor odor.
What is Construction Top Coat used for?
Nail art
What are the hazard statements for Construction Top Coat?
This substance has 6 hazard statements:
- H302: Ingestion: The product is expected harmful to Ingestion. directly swallowing the product will lead abdominal pain ,diarrhea Nausea .loss of appetite etc,and toxic if swallowed.
- H315: Skin: No known acute effects of this product resulting from skin contact, It will irritating damaged skin, and difficult to get rid it, However in light of good industrial hygiene exposure to any chemical should be kept to a minimum.
- H319: Eyes: Slightly hazardous by the following route of exposure: of eye contact (Irritant).
- H335: Inhalation: The volatile smell have a small amount of inhaled will be no risk.much inhaled will irritating respiratory tract.
- Potential Chronic Health Effects: .CARCINOGENIC EFFECTS: Not available. .MUTAGENIC EFFECTS: Not available. .TERATOGENIC EFFECTS: Not available.
- Medical Conditions Aggravated by Overexposure: There is no known effect from chronic exposure to this product. Repeated or prolonged exposure is not known to aggravate any medical condition. .Overexposure/ Signs/ Symptoms: No information available.
What is the melting point of Construction Top Coat?
The melting point is <0 °C and the boiling point is Not available.