MULTI-SPRAY PLUS 7

Remove person from danger area. Supply person with fresh air and consult doctor according to symptoms. If the person is unconscious, place in a stable side position and consult a doctor.

Wash thoroughly using copious water - remove contaminated clothing immediately. If skin irritation occurs (redness etc.), consult doctor.

Remove contact lenses. Wash thoroughly for several minutes using copious water. Seek medical help if necessary.

Rinse the mouth thoroughly with water. Do not induce vomiting. Consult doctor immediately. In case of vomiting, keep head low so that the stomach content does not reach the lungs.

Symptoms: Typically no exposure pathway. Danger of aspiration

Adapt to the nature and extent of fire. Water jet spray/foam/CO2/dry extinguisher

High volume water jet

In case of fire the following can develop: Oxides of carbon, Oxides of sulphur, Hydrocarbons, Toxic vapours, Danger of bursting (explosion) when heated, Explosive vapour/air or gas/air mixtures.

Cool container at risk with water.

Remove possible causes of ignition - do not smoke. Ensure sufficient ventilation. Avoid inhalation, and contact with eyes or skin. If applicable, caution - risk of slipping.

Prevent surface and ground-water infiltration, as well as ground penetration.

Soak up with absorbent material

Materials: universal binding agent, sand, diatomaceous earth

Ensure good ventilation. Avoid inhalation of the vapours. Keep away from sources of ignition - Do not smoke. Do not use on hot surfaces. Avoid contact with eyes or skin. Observe directions on label and instructions for use. Use working methods according to operating instructions.

Keep out of access to unauthorised individuals. Not to be stored in gangways or stair wells. Observe special storage conditions. Keep protected from direct sunlight and temperatures over 50°C. Store in a well ventilated place.

General hygiene measures for the handling of chemicals are applicable. Wash hands before breaks and at end of work. Keep away from food, drink and animal feedingstuffs. Remove contaminated clothing and protective equipment before entering areas in which food is consumed. Eating, drinking, smoking, as well as food-storage, is prohibited in work-room.

Keep away from sources of ignition - Do not smoke. Do not use on hot surfaces.

Ensure good ventilation. This can be achieved by local suction or general air extraction. If this is insufficient to maintain the concentration under the WEL or AGW values, suitable breathing protection should be worn. Applies only if maximum permissible exposure values are listed here. Suitable assessment methods for reviewing the effectiveness of protection measures adopted include metrological and non-metrological investigative techniques. These are specified by e.g. BS EN 14042. BS EN 14042 "Workplace atmospheres. Guide for the application and use of procedures for the assessment of exposure to chemical and biological agents".

Chemical resistant protective gloves (EN 374). If applicable Protective Neoprene® / polychloroprene gloves (EN 374). Protective nitrile gloves (EN 374) Minimum layer thickness in mm: 0,5 Permeation time (penetration time) in minutes: 480 The breakthrough times determined in accordance with EN 16523-1 were not obtained under practical conditions. The recommended maximum wearing time is 50% of breakthrough time. Protective hand cream recommended. Additional information on hand protection - No tests have been performed. In the case of mixtures, the selection has been made according to the knowledge available and the information about the contents. Selection of materials derived from glove manufacturer's indications. Final selection of glove material must be made taking the breakthrough times, permeation rates and degradation into account. Selection of a suitable glove depends not only on the material but also on other quality characteristics and varies from manufacturer to manufacturer. In the case of mixtures, the resistance of glove materials cannot be predicted and must therefore be tested before use. The exact breakthrough time of the glove material can be requested from the protective glove manufacturer and must be observed.

Tight fitting protective goggles with side protection (EN 166).

Normally not necessary. If OES or MEL is exceeded. Filter A2 P2 (EN 14387), code colour brown, white At high concentrations: Respiratory protection appliance (insulation device) (e.g. EN 137 or EN 138) Observe wearing time limitations for respiratory protection equipment.

Protective working garments (e.g. safety shoes EN ISO 20345, long-sleeved protective working garments).

No information available at present.

Stable with proper storage and handling.

Pressure increase will result in danger of bursting.

No dangerous reactions are known.

Heating, open flame, ignition sources. Pressure increase will result in danger of bursting.

Avoid contact with strong oxidizing agents.

No decomposition when used as directed.

Sewage disposal shall be discouraged. Pay attention to local and national official regulations. Take full aerosol cans to problem waste collection. Take emptied aerosol cans to valuable material collection.