Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- SikaForce®-420 L45 Part A
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Sealant/adhesive
Manufacturers & Suppliers
Sika Poland Spółka z o.o.
manufacturer
Karczunkowska 89 02-871 Warszawa
+48 22 27 28 700
Emergency Contacts
Emergency Contact
112
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Titanium dioxide (> 10 um) EC: 236-675-5 | 13463-67-7 | 5 - 10% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air.
Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water.
Remove contact lenses. Keep eye wide open while rinsing.
Do not induce vomiting without medical advice. Rinse mouth with water. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Maintain air concentrations below occupational exposure standards. Ensure adequate ventilation, especially in confined areas.
Chemical-resistant, impervious gloves complying with an approved standard must be worn at all times when handling chemical products. Reference number EN 374. Follow manufacturer specifications. Butyl rubber/nitrile rubber gloves (> 0,1 mm) Recommended: Butyl rubber/nitrile rubber gloves.
Safety glasses
In case of inadequate ventilation wear respiratory protection. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. organic vapor filter (Type A) A1: < 1000 ppm; A2: < 5000 ppm; A3: < 10000 ppm Ensure adequate ventilation. This can be achieved by local exhaust extraction or by general ventilation. (EN 689 - Methods for determining inhalation exposure). This applies in particular to the mixing / stirring area. In case this is not sufficent to keep the concentrations under the occupational exposure limits then respiration protection measures must be used.
Protective clothing (e.g. Safety shoes acc. to EN ISO 20345, long-sleeved working clothing, long trousers). Rubber aprons and protective boots are additionaly recommended for mixing and stirring work.
No special environmental precautions required.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for SikaForce®-420 L45 Part A?
The signal word is no signal word.
What is the physical form of SikaForce®-420 L45 Part A?
SikaForce®-420 L45 Part A is a liquid appearing as paste with various color. It has slight odor.
What is SikaForce®-420 L45 Part A used for?
Sealant/adhesive
What is the melting point of SikaForce®-420 L45 Part A?
The melting point is No data available and the boiling point is No data available.