NextSDS Logo
Safety Data Sheet EN

INTERNATIONAL THINNER-EQPT CLEANER

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
INTERNATIONAL THINNER-EQPT CLEANER
Product Code
GTA220

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Refer Technical Data Sheet.

Manufacturers & Suppliers

A

Akzo Nobel India Limited

manufacturer

Plot No. 62P, 62A, 62B, 43E, Hoskote Industrial Area, Pilgumpa Hoskote Taluk, Bangalore 562114. India

+91 80 22895000 / + 91 80 71717000

Emergency Contacts

Emergency Contact

+91 80 22895000

24 hour

Emergency Contact

+ 91 80 71717000

24 hour

Poisons Advice / Advice to Doctors & Hospitals

+91 80 22895000

Poisons Advice / Advice to Doctors & Hospitals

+ 91 80 71717000

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 3 H226
Skin Irrit. Cat. 2 H315
Eye Dam. Cat. 1 H318
STOT SE Cat. 3 H335
STOT SE Cat. 3 H335
Aquatic Chronic Cat. 2 H411

GHS Pictograms

GHS02 - Flammable

GHS02

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS09 - Environmental hazard

GHS09

Hazard Statements

H226 Flammable liquid and vapour.
H315 Causes skin irritation.
H318 Causes serious eye damage.
H335 May cause respiratory irritation.
H411 Toxic to aquatic life with long lasting effects.

Precautionary Statements

P210 Keep away from heat / sparks / open flames / hot surfaces - No smoking.
P260 Do not breathe mist / vapours / spray.
P261 Avoid breathing dust / fume / gas / mist / vapours / spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P273 Avoid release to the environment.
P280 Wear protective gloves / eye protection / face protection.
P310 Immediately call a POISON CENTER or doctor / physician.
P321 Specific treatment (see information on this label).
P331 Do NOT induce vomiting.
P362 Take off contaminated clothing and wash before reuse.
P370 In case of fire:
P378 Use alcohol resistant foam, CO2, powder, water spray for extinction. Do not use water jet.
P391 Collect spillage.
P405 Store locked up.
P501 Dispose of contents / container in accordance with local / national regulations.
IF SWALLOWED: Immediately call a POISON CENTER or doctor / physician.
IF ON SKIN: Wash with plenty of soap and water.
IF ON SKIN (or hair): Remove / Take off immediately all contaminated clothing. Rinse skin with water / shower.
IF INHALED: Call a POISON CENTER or doctor / physician if you feel unwell.
IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do - continue rinsing.
Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Store in a well ventilated place. Keep container tightly closed.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

This product contains the following substances that present a hazard.

Chemical Name CAS Number Concentration Hazardous
Xylene Mixture of Isomers 0001330-20-7 25 - 50% Yes
Solvent naphtha (petroleum), light aromatic 0064742-95-6 25 - 50% Yes
N-BUTANOL 0000071-36-3 10 - 25% Yes
1,2,4-trimethylbenzene 0000095-63-6 10 - 25% Yes
Ethylbenzene 0000100-41-4 2.5 - 10% Yes
1,3,5-trimethylbenzene 0000108-67-8 2.5 - 10% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove to fresh air, keep patient warm and at rest. If breathing is irregular or stopped, give artificial respiration. If unconscious place in the recovery position and obtain immediate medical attention. Give nothing by mouth.

Skin contact

Remove contaminated clothing. Wash skin thoroughly with soap and water or use a recognised skin cleanser. Do NOT use solvents or thinners.

Eye contact

Irrigate copiously with clean fresh water for at least 10 minutes, holding the eyelids apart and seek medical attention.

Ingestion

If accidentally swallowed obtain immediate medical attention. Keep at rest. Do NOT induce vomiting.

Immediate Medical Attention

In all cases of doubt, or when symptoms persist, seek medical attention. If unconscious, obtain immediate medical attention. If accidentally swallowed, obtain immediate medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

alcohol resistant foam, CO2, powder, water spray.

Unsuitable media

water jet.

Specific hazards

Fire will produce dense black smoke. Decomposition products may be hazardous to health.

Instructions

Cool closed containers exposed to fire by spraying them with water.

Firefighter Protection

Avoid exposure and use breathing apparatus as appropriate.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove sources of ignition, do not turn lights or unprotected electrical equipment on or off. In case of a major spill or spillage in a confined space evacuate the area and check that solvent vapour levels are below the Lower Explosive Limit before re-entering.

Large spill

In case of a major spill or spillage in a confined space evacuate the area

Environmental

Do not allow spills to enter drains or watercourses.

Cleanup methods

Clean, preferably with a detergent. Do not use solvents.

Materials: detergent

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Contains solvents. Solvent vapours are heavier than air and may spread along floors. Vapours may form explosive mixtures with air. Avoid skin and eye contact. Avoid inhalation of vapours and spray mists. Observe label precautions. Use personal protection as shown in section 8. Smoking, eating and drinking should be prohibited in all preparation and application areas. Never use pressure to empty a container. Use earthing leads when pouring solvents and transferring product. Operators should wear clothing which does not generate static (at least 60% natural fibre) and antistatic footwear.

Storage

Store in a well ventilated, dry place away from sources of heat and direct sunlight. Store on concrete or other impervious floor, preferably with bunding to contain any spillage. Do not stack more than 3 pallets high. Keep container tightly closed. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Keep in the original container or one of the same material.

Hygiene

Smoking, eating and drinking should be prohibited in all preparation and application areas.

Fire prevention

Naked flames and smoking should not be permitted in storage areas. All sources of ignition (hot surfaces, sparks, open flames etc) should be excluded from areas of preparation and application.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Provide adequate ventilation. Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction.

Hands

Gloves of an appropriate material should be worn during mixing and application.

Eyes

Wear safety eyewear, e.g. safety spectacles, goggles or visors to protect against the splash of liquids. Eyewear should comply with the appropriate standard. Wear a full face shield if mixing or pouring operations pose a risk of splashes.

Respiratory

If these are not sufficient to maintain concentrations of particulates and any vapour below occupational exposure limits suitable respiratory protection must be worn. When concentrations exceed the exposure limits shown above workers must wear appropriate approved respirators.

Skin/Body

Overalls which cover the body, arms and legs should be worn. Skin should not be exposed. Barrier creams may help to protect areas which are difficult to cover such as the face and neck. They should however not be applied once exposure has occurred. Petroleum jelly based types such as Vaseline should not be used.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Colourless Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
Colourless Liquid
Colour
Colourless
Colour Intensity
---
Form
---
Odor
Smell of Solvent
Odor Threshold
Not Measured
Ph
---
Melting Point
Not Measured
Boiling Point
116 °C
Flash Point
25 °C
Freezing Point
Not Measured
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not Measured
Vapor Pressure
Not Measured
Vapor Density
Heavier than air.
Relative Density
0.86
Bulk Density
---
Density
---
Flammability
Not Applicable
Upper Explosive Limit
11.3
Lower Explosive Limit
1.1
Explosive Limits
---
Auto Ignition Temperature
Not Measured
Decomposition Temperature
Not Measured
Solubility
---
Partition Coefficient
Not Measured
Solubility In Water
Immiscible
Solubility In Fat
---
Molecular Weight
---
Voc Content
---
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
---
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under recommended storage and handling conditions (see section 7). When exposed to high temperatures may produce hazardous decomposition products such as carbon monoxide, carbon dioxide, oxides of nitrogen and smoke.

Reactivity

No data available

Hazardous reactions

May react exothermically with: oxidising agents, strong alkalis, strong acids.

Avoid

Stable under recommended storage and handling conditions (see section 7).

Incompatible

Keep away from the following materials: oxidising agents, strong alkalis, strong acids.

Decomposition

Fire will produce dense black smoke. Decomposition products may include the following materials: carbon monoxide, carbon dioxide, smoke, oxides of nitrogen.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Do not allow into drains or water courses. Wastes and empty containers should be disposed of in accordance with local regulations.

Disposal

Using information provided in this data sheet advice should be obtained from the local Waste Regulation Authority as to whether special waste regulations apply.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1263
Shipping Name
Paint Related Material
Transport Class
3
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

This product and all its components complies with the chemical and transport regulations from the country listed in section 1.3.

Chemical Safety Assessment Not performed

None noted.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for INTERNATIONAL THINNER-EQPT CLEANER?

The signal word is danger.

What is the physical form of INTERNATIONAL THINNER-EQPT CLEANER?

INTERNATIONAL THINNER-EQPT CLEANER is a colourless liquid appearing as colourless liquid with colourless color. It has smell of solvent odor.

What is INTERNATIONAL THINNER-EQPT CLEANER used for?

Refer Technical Data Sheet.

What are the hazard statements for INTERNATIONAL THINNER-EQPT CLEANER?

This substance has 5 hazard statements:

  • H226: Flammable liquid and vapour.
  • H315: Causes skin irritation.
  • H318: Causes serious eye damage.
  • H335: May cause respiratory irritation.
  • H411: Toxic to aquatic life with long lasting effects.

What is the melting point of INTERNATIONAL THINNER-EQPT CLEANER?

The melting point is Not Measured and the boiling point is 116 °C.