Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Kalteinbettmittel Epoclear 2000 (Harz)
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
epoxy binder
Uses advised against
Any non-intended use.
Manufacturers & Suppliers
Schmitz-Metallographie GmbH
manufacturer
Kaiserstraße 100, D-52134 Herzogenrath
http://www.schmitz-metallographie.de
Dr. Timo Gans-Eichler (Chemieberatung)
Raesfeldstr. 22, D-48149 Münster
+49(0)251/394868-69
http://www.tge-consult.de
Emergency Contacts
Schmitz-Metallographie GmbH
02407 / 568296-0
Mo-Fr 9:00 - 16:00
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Epoxy resin formulation based on bisphenol A liquid resin and bisphenol F liquid resin
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| epoxy resin (number average molecular weight <= 700), reaction product: bisphenol-A-(epichlorhydrin) EC: 500-033-5 | 25068-38-6 | 50 - 100% | Yes |
| Formaldehyde, oligomeric reaction products with 1-chloro-2,3-epoxypropane and phenol EC: 500-006-8 | 9003-36-5 | 10 - 25% | Yes |
| 1,6-bis(2,3-epoxypropoxy)hexane EC: 240-260-4 | 16096-31-4 | 10 - 25% | Yes |
Notes
Product does not contain listed SVHC substances > 0,1 % according to Regulation (EC) No. 1907/2006 Article 59 (REACH)
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of accident by inhalation: remove casualty to fresh air and keep at rest. In all cases of doubt, or when symptoms persist, seek medical advice.
After contact with skin, wash immediately with plenty of water and soap. Take off immediately all contaminated clothing. In case of skin irritation, consult a physician.
Rinse immediately carefully and thoroughly with eye-bath or water. In case of troubles or persistent symptoms, consult an ophthalmologist.
Rinse mouth thoroughly with water. Let water be drunken in little sips (dilution effect). Do NOT induce vomiting. In all cases of doubt, or when symptoms persist, seek medical advice.
Immediate Medical Attention
Treat symptomatically.
Medical Treatment
Treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Sand. Foam. Carbon dioxide (CO2). Extinguishing powder. In case of major fire and large quantities: Water spray jet. Water mist.
High power water jet
Can be released in case of fire: Carbon monoxide Carbon dioxide (CO2)
In case of fire and/or explosion do not breathe fumes. Co-ordinate fire-fighting measures to the fire surroundings.
Firefighter Protection
In case of fire: Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not allow to enter into surface water or drains. Prevent spread over a wide area (e.g. by containment or oil barriers). Do not allow to enter into soil/subsoil.
Absorb with liquid-binding material (e.g. sand, diatomaceous earth, acid- or universal binding agents).
Materials: sand, diatomaceous earth, acid- or universal binding agents
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Wear suitable protective clothing. (See section 8.)
Keep container tightly closed in a cool, well-ventilated place. Only use containers specifically approved for the substance/product.
Advices on general occupational hygiene: See section 8.
Usual measures for fire prevention.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide adequate ventilation.
In case of prolonged or frequently repeated skin contact: Wear suitable gloves. Suitable material: FKM (fluororubber). - Thickness of glove material: 0,4 mm Breakthrough time >= 8 h. Butyl rubber. - Thickness of glove material: 0,5 mm Breakthrough time >= 8 h. CR (polychloroprenes, Chloroprene rubber). - Thickness of glove material: 0,5 mm Breakthrough time >= 8 h. NBR (Nitrile rubber). - Thickness of glove material: 0,35 mm Breakthrough time >= 8 h. PVC (Polyvinyl chloride). - Thickness of glove material: 0,5 mm Breakthrough time >= 8 h. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it. Before using check leak tightness / impermeability. In the case of wanting to use the gloves again, clean them before taking off and air them well.
Wear safety glasses; chemical goggles (if splashing is possible). DIN EN 166
With correct and proper use, and under normal conditions, breathing protection is not required. Respiratory protection necessary at: - exceeding exposure limit values - insufficient ventilation and aerosol or mist formation Suitable respiratory protective equipment: particulates filter device (DIN EN 143). Type: P1-3 The filter class must be suitable for the maximum contaminant concentration (gas/vapour/aerosol/particulates) that may arise when handling the product. If the concentration is exceeded, self-contained breathing apparatus must be used. Observe the wear time limits according GefStoffV in combination with the rules for using respiratory protection apparatus (BGR 190).
Suitable protective clothing: Lab apron. Minimum standard for preventive measures while handling with working materials are specified in the TRGS 500.
No information available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under recommended conditions of storage, use and temperature.
No information available.
No information available.
Protect against: UV-radiation/sunlight. heat.
Materials to avoid: Oxidizing agents, strong. Reducing agents, strong.
No known hazardous decomposition products.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of waste according to applicable legislation. Consult the local waste disposal expert about waste disposal.
Dispose of waste according to applicable legislation.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (epoxy resin (number average molecular weight <= 700), reaction product: bisphenol-A-(epichlorhydrin))
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Kalteinbettmittel Epoclear 2000 (Harz)?
The signal word is warning.
What is the physical form of Kalteinbettmittel Epoclear 2000 (Harz)?
Kalteinbettmittel Epoclear 2000 (Harz) is a liquid with yellowish color. It has characteristic odor.
What is the solubility of Kalteinbettmittel Epoclear 2000 (Harz)?
No information available.
What is Kalteinbettmittel Epoclear 2000 (Harz) used for?
epoxy binder
What are the hazard statements for Kalteinbettmittel Epoclear 2000 (Harz)?
This substance has 4 hazard statements:
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of Kalteinbettmittel Epoclear 2000 (Harz)?
The melting point is No information available. and the boiling point is >200 °C.