Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- LUBRICANT FOR PIPE THREADING AND METAL FORMING
- Product Code
- 11931, 11531, 16951, 27521, 41585
Regulatory Identifiers
- CAS Number
- N/A
- REACH No.
- Mixture
Identified Uses
Lubricant
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
RIDGE TOOL EUROPE N.V.
manufacturer
Interleuvenlaan 50, 3001 Heverlee, Belgium
0032 (0) 16 380 280
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
A blend of highly refined mineral oils with multifunctional additives.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Nonionic surfactant EC: 500-195-7 | 68131-39-5 | 2.5% | Yes |
For the wording of the listed risk phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Symptoms: skin irritation
Rinse opened eye for several minutes under running water. Then consult a doctor.
Do not induce vomiting; call for medical help immediately.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Goggles recommended during refilling
Not required.
Oil resistant protective clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Void
- Shipping Name
- Void
- Transport Class
- Void
- Packing Group
- Void
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for LUBRICANT FOR PIPE THREADING AND METAL FORMING?
The signal word is no signal word.
What is the physical form of LUBRICANT FOR PIPE THREADING AND METAL FORMING?
LUBRICANT FOR PIPE THREADING AND METAL FORMING is a fluid with brown color. It has pleasant odor.
What is LUBRICANT FOR PIPE THREADING AND METAL FORMING used for?
Lubricant
What is the melting point of LUBRICANT FOR PIPE THREADING AND METAL FORMING?
The melting point is Undetermined. and the boiling point is > 250.