Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Laboratory use. For product use see insert.
Uses advised against
Not to be used for any purpose other than those mentioned below.
Manufacturers & Suppliers
Fujirebio Inc.
manufacturer
2-1-1 Nishishinjuku, Shinjuku-ku, Tokyo 163-0410, Japan
Fujirebio Europe N.V.
distributor
Technologiepark 6, 9052 Zwijnaarde, Belgium
Emergency Contacts
Fujirebio Inc. (Japan) Global Sales Department
+81-3-6279-0899
Mon - Fri 9:00am to 5:30pm (JST)
Fujirebio Europe N.V.
+32-9-329-13-29
Mon - Fri 9:00am to 5:30pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 4-morpholinopropanesulphonic acid EC: 214-478-5 | 1132-61-2 | 2.5% | Yes |
| reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1) | 55965-84-9 | 0.0025 - 0.025% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Do not induce vomiting; call for medical help immediately.
Immediate Medical Attention
call for medical help immediately
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray. Use fire extinguishing methods suitable to surrounding conditions.
No further relevant information available.
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Not required.
Do not allow product to reach sewage system or any water course.
Absorb liquid components with liquid-binding material.
Materials: liquid-binding material
Related Products
Similar products with comparable safety profiles
Lumipulse G β-Amyloid 1-42 Plasma IRC, Particle solution
---
Lumipulse G pTau 217 Plasma CAL
---
Lumipulse G NfL Blood IRC, Particle solution
---
Lumipulse G pTau 181 Plasma Calibrators, CAL 1, CAL 2, CAL 3, CAL 4, CAL 5
---
Lumipulse G NfL CSF IRC, Particle solution
---
Lumipulse β-Amyloid Plasma Controls (L 1, L 2)
---
Polyclonal Rabbit Antibody Solution
---
Luminase; LumiAMP (Rehydrated)
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
See section 8 (Measurements for the control of exposure / personal protection).
Store in a dry and well-ventilated area in the closed original packaging. Respect the expiry date and the additional instruction given in the package insert.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Wear protective gloves in order to be protected against chemical risks according to EN 420 and EN 374. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Penetration time of glove material: As the product is a preparation consisting of different substances, no specific information can be given about breakthrough times. The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. As protection from splashes gloves made of the following materials are suitable: Nitrile rubber, NBR. Recommended thickness of the material: 0.11 mm
Wear safety glasses in order to protect your eyes against chemical splashes according to EN 166.
Not necessary if room is well-ventilated.
Wear a laboratory coat for your protection against chemical splashes according to EN 340 and EN 369.
Comply with the current local and national environmental regulations.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No further relevant information available.
No further relevant information available.
No hazardous reactions are known.
No further relevant information available.
No further relevant information available.
No decomposition if used according to specifications.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of contents in accordance with local / regional/ national/ international regulations.
Dispose of contents in accordance with local / regional/ national/ international regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- void
- Shipping Name
- void
- Transport Class
- void
- Packing Group
- void
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution?
The signal word is warning.
What is the physical form of Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution?
Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution is a liquid @23-27°c, gel-like solid @2-8°c with slightly yellow color. It has odourless odor.
What is Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution used for?
Laboratory use. For product use see insert.
What are the hazard statements for Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution?
This substance has 2 hazard statements:
- H317: May cause an allergic skin reaction.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Lumipulse G pTau 181 Immunoreaction Cartridges : Antibody-Coated Particle Solution?
The melting point is Undetermined. and the boiling point is Undetermined..