NextSDS Logo
Safety Data Sheet EN

FORMALDEHYDE SOLUTION, 37-40%w/w aq

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
FORMALDEHYDE SOLUTION, 37-40%w/w aq
Product Code
BFORM5000 BFORM2500 BSBFORM1000

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Fixative for tissues to be examined by microscopy, SU20 Health services and SU24 Scientific Research and Development.

Manufacturers & Suppliers

P

Proteome

manufacturer

2 Twineham Gardens, Alderbury, Salisbury, Wiltshire, SP5 3TF

Emergency Contacts

Proteome

+44(0) 7523 657252

Mon to Friday 9am – 4pm

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Carc. Cat. 1B
Muta. Cat. 2
Acute Tox. Cat. 3
Acute Tox. Cat. 3
Acute Tox. Cat. 3
Skin Corr. Cat. 1B H314
Skin Sens. Cat. 1 H317
Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2 H319
STOT SE Cat. 3 H335

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

GHS08 - Serious health hazard

GHS08

Hazard Statements

H301 Toxic if swallowed
H311 Toxic in contact with skin
H314 Causes severe skin burns and eye damage
H317 May cause an allergic skin reaction
H331 Toxic if inhaled
H335 May cause respiratory irritation
H341 Suspected of causing genetic defects
H350 May cause cancer by inhalation

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe mist/vapours/spray.
P264 Wash thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P304 + P340 IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical advice/ attention.
P310 Immediately call a POISON CENTER or doctor/physician.
P363 Wash contaminated clothing before reuse.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local and national regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Formaldehyde EC: 200-001-8 50-00-0 36% Yes
Methanol EC: 200-659-6 67-56-1 10% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove casualty from exposure ensuring one's own safety whilst doing so. If conscious, ensure the casualty sits or lies down. If unconscious and breathing is OK, place in the recovery position. If unconscious, check for breathing and apply artificial respiration if necessary. If breathing becomes bubbly, have the casualty sit and provide oxygen if available. Transfer to hospital as soon as possible.

Symptoms: Shortness of breath with a burning sensation in the throat. Absorption through the lungs can occur causing symptoms similar to those of ingestion. Convulsions may occur. There may be loss of consciousness.

Skin contact

Remove all contaminated clothes and footwear immediately unless stuck to skin. Drench the affected skin with running water for 10 minutes or longer if substance is still on skin. Transfer to hospital if there are burns or symptoms of poisoning.

Symptoms: There may be redness or whiteness of the skin in the area of exposure. Irritation or pain may occur at the site of contact. Absorption through the skin may be fatal.

Eye contact

Bathe the eye with running water for 15 minutes. Transfer to hospital for specialist examination.

Symptoms: There may be severe pain. The eyes may water profusely.

Ingestion

Wash out mouth with water. Do not induce vomiting. If conscious, give half a litre of water to drink immediately. If unconscious, check for breathing and apply artificial respiration if necessary. If unconscious and breathing is OK, place in the recovery position. Transfer to hospital as soon as possible.

Symptoms: There may be soreness and redness of the mouth and throat. There may be vomiting. Convulsions may occur. There may be loss of consciousness.

Immediate Medical Attention

Immediate medical attention is required.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Suitable extinguishing media for the surrounding fire should be used. Use water spray to cool containers.

Specific hazards

Toxic. In combustion emits toxic fumes.

Firefighter Protection

Wear self-contained breathing apparatus. Wear protective clothing to prevent contact with skin and eyes.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Notify the police and fire brigade immediately. If outside do not approach from downwind. If outside keep bystanders upwind and away from danger point. Mark out the contaminated area with signs and prevent access to unauthorised personnel. Do not attempt to take action without suitable protective clothing - see section 8 of SDS.

Environmental

Do not discharge into drains or rivers. Contain the spillage using bunding.

Cleanup methods

Absorb into dry earth or sand. Transfer to a closable, labelled salvage container for disposal by an appropriate method.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent eye and skin contact. Do not breathe vapours or mists. Use only with adequate ventilation. Wash thoroughly after handling. Remove contaminated clothing and launder before re-use. Keep containers closed when not in use.

Storage

Protect containers from physical damage. Keep containers closed when not in use. Store away from oxidizer and away from direct sunlight and other sources of ignition. Optimum storage temperature: 15-25 °C. Cold temperatures encourage the formation of trioxymethylene with a resulting white precipitate.

Hygiene

Wash thoroughly after handling. Remove contaminated clothing and launder before re-use.

Fire prevention

Store away from sources of ignition.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Ensure there is exhaust ventilation of the area.

Hands

Impermeable gloves.

Eyes

Safety glasses with side-shields. Ensure eye bath is to hand.

Respiratory

Self-contained breathing apparatus must be available in case of emergency.

Skin/Body

Impermeable protective clothing.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
Colourless
Colour
Colourless
Colour Intensity
---
Form
---
Odor
Pungent
Odor Threshold
No data available
Ph
No data available
Melting Point
No data available
Boiling Point
101°C/213.8°F
Flash Point
85°C
Freezing Point
No data available
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
No data available
Vapor Pressure
No data available
Vapor Density
---
Relative Density
1.080g/cm3
Bulk Density
---
Density
---
Flammability
No data available
Upper Explosive Limit
No data available
Lower Explosive Limit
No data available
Explosive Limits
---
Auto Ignition Temperature
No data available
Decomposition Temperature
No data available
Solubility
---
Partition Coefficient
---
Solubility In Water
completely soluble
Solubility In Fat
---
Molecular Weight
---
Voc Content
---
Metal Corrosion
---
Dynamic Viscosity
No data available
Kinematic Viscosity
No data available
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions

Reactivity

Stable under recommended transport and storage conditions

Hazardous reactions

Hazardous reactions will not occur under normal transport or storage conditions. Decomposition may occur on exposure to conditions or materials listed below

Avoid

Heat. Hot surfaces. Flames.

Incompatible

Strong bases, Acids, Oxidising agents, Alkali metals, Strong oxidising agents, Amines, Acid chlorides, Acid anhydrides, Reducing agents, Peroxides, Isocyanates, Phenols, Aniline.

Decomposition

In combustion emits toxic fumes.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Transfer to a suitable container and arrange for collection by specialised disposal company.

Disposal

Transfer to a suitable container and arrange for collection by specialised disposal company.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN2209
Shipping Name
FORMALDEHYDE SOLUTION
Transport Class
8
Packing Group
III
ADR

No data available

IMDG

No data available

IATA

No data available

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

No data available

Chemical Safety Assessment Not performed
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for FORMALDEHYDE SOLUTION, 37-40%w/w aq?

The signal word is danger.

What is the physical form of FORMALDEHYDE SOLUTION, 37-40%w/w aq?

FORMALDEHYDE SOLUTION, 37-40%w/w aq is a liquid appearing as colourless with colourless color. It has pungent odor.

What is FORMALDEHYDE SOLUTION, 37-40%w/w aq used for?

Fixative for tissues to be examined by microscopy, SU20 Health services and SU24 Scientific Research and Development.

What are the hazard statements for FORMALDEHYDE SOLUTION, 37-40%w/w aq?

This substance has 8 hazard statements:

  • H301: Toxic if swallowed
  • H311: Toxic in contact with skin
  • H314: Causes severe skin burns and eye damage
  • H317: May cause an allergic skin reaction
  • H331: Toxic if inhaled
  • H335: May cause respiratory irritation
  • H341: Suspected of causing genetic defects
  • H350: May cause cancer by inhalation

What is the melting point of FORMALDEHYDE SOLUTION, 37-40%w/w aq?

The melting point is No data available and the boiling point is 101°C/213.8°F.