Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MR® 76 S Magnetic powder suspension, black
- Product Form
- Aerosol
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Testing material for nondestructive surface crack detection
Manufacturers & Suppliers
MR® Chemie GmbH
manufacturer
Nordstr. 61-63, 59427 Unna (Germany)
+49 (0)2303 95151 0
https://www.mr-chemie.de
Emergency Contacts
USA and Canada
1 800 424 9300
Outside USA and Canada
001 703 527 3887
Germany
0800-181-7059
China
4001 204937
ZH
Hong Kong
800 968 793
ZH
India
000 800 100 7141
HI
South Africa
0 800 983 611
EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| isoparaffinic hydrocarbons | --- | 50 - 60% | Yes |
| propane EC: 200-827-9 | 74-98-6 | 25 - 30% | Yes |
| butane (containing ≤ 0,1 % butadiene (203-450-8)) EC: 203-448-7 | 106-97-8 | 25 - 30% | Yes |
Propellant: Propane-Butane. For the wording of the listed hazard phrases refer to section 16.
Notes
Propellant: Propane-Butane
First Aid Measures
Emergency procedures for chemical exposure incidents
Take affected persons into fresh air and keep quiet. Seek medical treatment in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Not relevant - aerosol can.
Immediate Medical Attention
Seek medical treatment in case of complaints (inhalation), consult a doctor (eye).
Medical Treatment
With aspiration danger of the pulmonary edema and/or pneumonia.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
In case of fire, the following can be released: Carbon monoxide (CO)
Cool endangered receptacles with water spray.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure adequate ventilation. Keep away from ignition sources. Wear protective equipment. Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Dispose contaminated material as waste according to item 13.
Related Products
Similar products with comparable safety profiles
MR® 76 S Magnetic powder suspension, black, ready for use, Version A Aerosol
---
MR® 76 FA Magnetic powder suspension (Aerosol)
---
MR® 72 AF Contrast paint white (Aerosol)
---
MR® 79 Special Cleaner
---
MR® 68 C Penetrant
---
MR® 68 NF Penetrant
---
MR® 751 Special Ultrasonic coupling agent
---
MR® Contrast paint white (Aerosol)
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No special precautions are necessary if used correctly.
Store in a cool location. Observe official regulations on storing packagings with pressurised containers. Store away from foodstuffs. Protect from heat and direct sunlight.
Do not spray onto a naked flame or any incandescent material. Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
For good ventilation provide, this can be achieved by local or space exhaust. No further data; see item 7.
Nitrile rubber, NBR; Fluorocarbon rubber (Viton); Recommended thickness of the material: ≥ 0.5 mm; Value for the permeation: Level ≤ 6. Check the permeability prior to each anewed use of the glove. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses
Filter AX-P2. If the concentration lies over the job limit values, then, a certified respirator suitable for this purpose must be used.
Protective work clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No further relevant information available.
No dangerous reactions known.
Avoid open flame or electrical ignition. Danger of bursting of the aerosol can during overheating
Strong oxidizing agents.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Eliminate the pure, unchanged substance in accordance with local regulations.
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2.1
- Packing Group
- Void
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MR® 76 S Magnetic powder suspension, black?
The signal word is danger.
What is the physical form of MR® 76 S Magnetic powder suspension, black?
MR® 76 S Magnetic powder suspension, black is a aerosol with black color. It has characteristic odor.
What is MR® 76 S Magnetic powder suspension, black used for?
Testing material for nondestructive surface crack detection
What are the hazard statements for MR® 76 S Magnetic powder suspension, black?
This substance has 1 hazard statement:
- H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
What is the melting point of MR® 76 S Magnetic powder suspension, black?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..