Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- WACKER® PLASTICIZER 100
- Synonyms
- SILICONE PLASTICIZER
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Industrial. Raw material for: elastomer products.
Manufacturers & Suppliers
Wacker Chemie AG
manufacturer
Gisela-Stein-Straße 1 81671 München Germany
Wacker Chemical Corporation
4950 S State Road Ann Arbor, MI 48108
(517) 264-8240
www.wacker.com
Emergency Contacts
Emergency Contact
(517) 264-8500
24h
CHEMTREC, USA
(800) 424-9300
CHEMTREC, international
(703) 527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
This material does not contain any ingredients above the permitted limit(s). This product does not contain substances of very high concern (Regulation (EC) No 1907/2006 (REACH), Article 57) in amounts above ≥ 0.1%.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Polydimethylsiloxane | --- | --- | No |
Notes
Substances listed in the Subsections "HAPS" and "California Proposition 65 Carcinogens / Reproductive Toxins" that are not listed in this section are only present at quantities below 0.1% for California Proposition 65 listed toxins or below 1% for non-carcinogenic HAPS or they are inextricably bound in the product.
First Aid Measures
Emergency procedures for chemical exposure incidents
No special treatment required.
After skin contact wipe off excess material with cloth or paper. Use a waterless hand cleaner to remove as much of the remaining material as possible. Wash with soap and water.
If contact with eyes, immediately hold eyelids apart and flush with plenty of water for at least 15 min.
No special measures are required after swallowing.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
water-mist, carbon dioxide, sand, dry chemical or alcohol-resistant foam.
water-spray, sharp water jet.
This material does not present any unusual fire or explosion hazards.
Cool endangered containers with water.
Firefighter Protection
Fire fighters should wear full protective clothing including a self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Secure the area. Wear personal protection equipment (see section 8). Keep unprotected persons away. If material is released indicate risk of slipping. Do not walk through spilled material.
For small amounts: Absorb with a neutral (non-acidic / non-basic) liquid binding material such as diatomaceous earth and dispose of according to government regulations.
For large amounts: Liquids may be recovered using suction devices or pumps. If flammable, only air driven or properly rated electrical equipment should be used.
Prevent material from entering surface waters, drains or sewers and soil. Retain contaminated water/extinguishing water.
Take up mechanically and dispose of according to local/state/federal regulations. Do not flush away with water. For small amounts: Absorb with a neutral (non-acidic / non-basic) liquid binding material such as diatomaceous earth and dispose of according to government regulations. For large amounts: Liquids may be recovered using suction devices or pumps. If flammable, only air driven or properly rated electrical equipment should be used. Clean any slippery coating that remains using a detergent / soap solution or another biodegradable cleaner. Silicone fluids are slippery; spills are a safety hazard. Apply sand or other inert granular material to improve traction.
Materials: neutral (non-acidic / non-basic) liquid binding material such as diatomaceous earth; detergent / soap solution or another biodegradable cleaner; sand or other inert granular material
Related Products
Similar products with comparable safety profiles
S-2075 PLASTICIZER
CAS: 94-28-0
WACKER® Vinylacetat Monomer stab.
---
WACKER® AK 350 SILICONE FLUID
---
WACKER® AK 350 SILICONE FLUID
---
Eastman Effusion(TM) Plasticizer
---
Eastman Effusion(TM) Plasticizer
CAS: 1962-75-0
Eastman 168(TM) non-phthalate plasticizer
---
Wax dispersant WD 4105
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid formation of aerosols. In case of aerosol formation special protective measures are required (exhausting by suction, respiratory protection). Spilled substance increases risk of slipping. Observe information in section 8.
Observe local/state/federal regulations. Store in a dry and cool place.
Observe the general rules for fire prevention.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use with adequate ventilation. Local exhaust not necessary.
Recommendation: Any liquid-tight rubber or vinyl gloves.
Recommendation: Safety glasses with side shields.
Respiratory protection is not normally required.
Additional protective clothing or equipment is not normally required.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
If stored and handled in accordance with standard industrial practices no hazardous reactions are known.
If stored and handled in accordance with standard industrial practices no hazardous reactions are known.
Hazardous polymerization cannot occur.
None known.
None known.
If stored and handled properly: none known. Measurements have shown the formation of small amounts of formaldehyde at temperatures above about 150 °C (302 °F) through oxidation.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is WACKER® PLASTICIZER 100 known by?
WACKER® PLASTICIZER 100 is also known as: SILICONE PLASTICIZER
What is the hazard signal word for WACKER® PLASTICIZER 100?
The signal word is no signal word.
What is the physical form of WACKER® PLASTICIZER 100?
WACKER® PLASTICIZER 100 is a liquid appearing as colorless transparent with colorless transparent color. It has odourless odor.
What is WACKER® PLASTICIZER 100 used for?
Industrial. Raw material for: elastomer products.
What is the melting point of WACKER® PLASTICIZER 100?
The melting point is -55 °C (-67 °F) and the boiling point is not determinable.