WACKER® CATALYST T 21

Keep the patient calm. If unconscious place in stable sideways position. Protect against loss of body heat. Seek medical advice and clearly identify substance.

Wipe off excess material with cloth or paper. Remove contaminated or soaked clothing. Immediately rinse with plenty of soap and water. In serious cases, use emergency shower immediately. In the event of a visible skin change or other complaints, seek medical advice (show label or SDS where possible).

Rinse immediately with plenty of water for 10-15 minutes. Keep eyelids well open to rinse the whole eye surface and eyelids with water. Seek medical advice in case of continuous irritation.

If conscious, give several small portions of water to drink. Do not induce vomiting. Seek medical advice and clearly identify substance.

alcohol-resistant foam, carbon dioxide, water mist, sprinkler system, sand, extinguishing powder.

water jet.

Risk of hazardous gasses or fumes in the event of fire. Exposure to combustion products may be a health hazard!

Keep unprotected persons away.

Secure the area. Keep unprotected persons away. Avoid contact with eyes and skin. Do not inhale gases/vapours/aerosols. If material is released indicate risk of slipping. Do not walk through spilled material.

Absorb with a neutral (non-acidic / non-basic) liquid binding material such as diatomaceous earth and dispose of according to government regulations.

Liquids may be recovered using suction devices or pumps. If flammable, only air driven or properly rated electrical equipment should be used.

Prevent material from entering surface waters, drains or sewers and soil.

Take up mechanically. Clean any slippery coating that remains using a detergent / soap solution or another biodegradable cleaner.

Materials: detergent / soap solution or another biodegradable cleaner

Ensure adequate ventilation. Must be syphoned off in situ. Spilled substance increases risk of slipping. Avoid formation of aerosols. In case of aerosol formation special protective measures are required (exhausting by suction, respiratory protection). Observe information in section 8. Keep away from incompatible substances in accordance with section 10.

Store in a dry and cool place. Protect against moisture. Store container in a well ventilated place.

Keep away from sources of ignition and do not smoke. Take precautionary measures against electrostatic charging. Cool endangered containers with water.

Use with adequate ventilation.

Gloves are required at all times when handling the material. Recommended glove types: Protective gloves made of butyl rubber thickness of the material: > 0,3 mm. Breakthrough time: > 480 min. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion, and the contact time.

tight fitting protective goggles.

If inhalative exposure above the occupational exposure limit cannot be excluded, adequate respiratory protection equipment must be used. Suitable respiratory equipment: Respirator with a full face mask, according to acknowledged standards such as EN 136. Recommended Filter type: Gas filter type ABEK (certain inorganic, organic and acidic gases and vapors; ammonia/amines), according to acknowledged standards such as EN 14387. In case of mist, spray or aerosol exposure wear suitable personal respiratory protection and protective suit. Suitable respiratory equipment: Respirator with a full face mask, according to acknowledged standards such as EN 136. Recommended Filter type: Combined filter type ABEK-P2 (certain inorganic, organic and acidic gases and vapors; ammonia/amines; particles), according to acknowledged standards such as EN 14387. For long or intense exposure, use respiratory protective equipment. Suitable respiratory equipment: Positive pressure self contained breathing apparatus, according to acknowledged standards such as EN 137. Observe the equipment manufacturer's information and wear time limits for respirators.

If handled uncovered: Chemical protective clothing, full-body liquid-tight protection if necessary. Please observe the instructions regarding permeability time which are provided by the supplier.

Prevent material from entering surface waters, drains or sewers and soil. Observe local waste water bye-laws for organo tin and tin compounds. Do not introduce large amounts into purification plants.

If stored and handled in accordance with standard industrial practices no hazardous reactions are known.

no hazardous reactions are known

moisture, Heat, open flames, and other sources of ignition.

water, basic substances and acids

alcohols

landfill or incineration

Material that cannot be used, reprocessed or recycled should be disposed of in accordance with Federal, State, and local regulations at an approved facility.