Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- NovoFlow 8515/B
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coating product for fertilizers.
Manufacturers & Suppliers
HOLLAND NOVOCHEM B.V.
manufacturer
Papiermolen 5, 3994 DJ Houten, The Netherlands
+31 (0)30 - 602 15 33
http://www.novochemgroup.com
Emergency Contacts
HOLLAND NOVOCHEM B.V.
+31 (0)30 - 602 15 33
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Blend of surface active components in mineral oils and mineral waxes.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| organic P-compounds | --- | 5 - 10% | Yes |
| alkyl amine | --- | 5 - 10% | Yes |
The product does not contain substances mentioned on the SVHC-list (Annex XIV of REACH).
Notes
SVHC The product does not contain substances mentioned on the SVHC-list (Annex XIV of REACH).
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of inhalation of hot vapours, immediately supply fresh air. If required, provide artificial respiration. Keep patient warm. Obtain medical advice if symptoms persist.
Immediately wash with water and soap and rinse thoroughly. Wash contact areas with soap and water. If burned by contact with hot material, molten material adhering to skin should be cooled as quickly as possible with water, and see a physician for removal of adhering material and treatment of burn.
Rinse opened eye for at least 15 minutes under running water. Get immediate medical attention. In case of contact with hot product, flood with water to dissipate heat. In the event of any material remaining, do not try to remove it other than by continued irrigation with water. Obtain medical attention immediately.
Rinse out mouth and then drink plenty of water.
Immediate Medical Attention
Get immediate medical attention (for eyes); see a physician for removal of adhering material and treatment of burn (for skin).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, sand, extinguishing powder, water spray jet.
Water with full jet.
In case of fire, the following can be released: Nitrogen oxides (NOx) Carbon monoxide and carbon dioxide (COx) Phosphor oxides (POx)
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Clean up spillages promptly as these may make surfaces slippery. Avoid contact with molten product and vapour inhalation from hot waxes.
Do not allow to enter sewers/ surface or ground water.
Pick up solid material mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes and skin. Avoid contact with molten product. Wear personal protective clothing (see section 8).
Keep receptacle tightly sealed.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Eye wash possibility with fresh water.
Synthetic rubber gloves (butyl, nitril). The determined penetration times according to EN 16523-1:2015 are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended.
Safety goggles when handling the molten/heated product if there is danger of splashing.
Protective mask in case of hot vapours.
Protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at room temperature, in closed packaging, at normal storage and handling conditions.
No further relevant information available.
Reacts with strong oxidizing agents
No further relevant information available.
No further relevant information available.
In case of fire or overheating the following products can be released: Carbon monoxide and carbon dioxide (COx) Nitrogen oxides (NOx) Phosphorus oxides (POx)
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
After prior treatment product has to be disposed of in an incinerator for hazardous waste adhering to the regulations pertaining to the disposal of particularly hazardous waste.
After prior treatment product has to be disposed of in an incinerator for hazardous waste adhering to the regulations pertaining to the disposal of particularly hazardous waste.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3077
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (alkyl amine)
- Transport Class
- 9
- Packing Group
- III
Warning: Miscellaneous dangerous substances and articles.
Warning: Miscellaneous dangerous substances and articles.
Warning: Miscellaneous dangerous substances and articles.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for NovoFlow 8515/B?
The signal word is danger.
What is the physical form of NovoFlow 8515/B?
NovoFlow 8515/B is a pasty appearing as pasty with yellow to brown color. It has typical odor.
What is NovoFlow 8515/B used for?
Coating product for fertilizers.
What are the hazard statements for NovoFlow 8515/B?
This substance has 2 hazard statements:
- H314: Causes severe skin burns and eye damage.
- H410: Very toxic to aquatic life with long lasting effects.
What is the melting point of NovoFlow 8515/B?
The melting point is 40-50 °C and the boiling point is >250 °C.