Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Nopcomaster™ ENA 2100 DEFOAMER
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Defoamer
Manufacturers & Suppliers
Solenis Netherlands B.V.
manufacturer
De Corridor 4, 3621 ZB Breukelen, Netherlands
Emergency Contacts
Emergency Contact
+1-302-502-0991
Emergency Contact
112
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 1,2-benzisothiazol-3(2H)-one EC: 220-120-9 | 2634-33-5 | 0.025 - 0.05% | Yes |
| mixture of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no.247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1) | 55965-84-9 | 0.0002 - 0.0015% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If breathed in, move person into fresh air. If unconscious, place in recovery position and seek medical advice. If symptoms persist, call a physician.
First aid is not normally required. However, it is recommended that exposed areas be cleaned by washing with soap and water.
Remove contact lenses. Protect unharmed eye.
Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician.
Immediate Medical Attention
If symptoms persist, call a physician.
Medical Treatment
No hazards which require special first aid measures.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Water spray, Foam, Carbon dioxide (CO2), Dry chemical
If product is heated above its flash point it will produce vapors sufficient to support combustion. Vapors are heavier than air and may travel along the ground and be ignited by heat, pilot lights, other flames and ignition sources at locations near the point of release.
Standard procedure for chemical fires.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Comply with all applicable federal, state, and local regulations.
Prevent further leakage or spillage if safe to do so.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Keep in suitable, closed containers for disposal.
Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Smoking, eating and drinking should be prohibited in the application area. For personal protection see section 8.
5 - 35 °C
General industrial hygiene practice.
Normal measures for preventive fire protection.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
General room ventilation should be adequate for normal conditions of use. However, if unusual operating conditions exist, provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below exposure guidelines (if applicable) or below levels that cause known, suspected or apparent adverse effects.
Wear resistant gloves (consult your safety equipment supplier).
Not required under normal conditions of use. Wear splash-proof safety goggles if material could be misted or splashed into eyes.
No personal respiratory protective equipment normally required.
Wear as appropriate: Safety shoes
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
No decomposition if stored and applied as directed.
Product will not undergo hazardous polymerization.
No data available
Oxidizing agents, strong mineral acids
Carbon monoxide, Carbon dioxide (CO2), Hydrocarbons
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of in accordance with local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Nopcomaster™ ENA 2100 DEFOAMER?
The signal word is no signal word.
What is the physical form of Nopcomaster™ ENA 2100 DEFOAMER?
Nopcomaster™ ENA 2100 DEFOAMER is a emulsion with off-white, light yellow color. It has no data available odor.
What is Nopcomaster™ ENA 2100 DEFOAMER used for?
Defoamer
What is the melting point of Nopcomaster™ ENA 2100 DEFOAMER?
The melting point is No data available and the boiling point is 100 °C.