Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ANIOXYDE 1000_RECONSTITUE
- Product Code
- 1081/A1000
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cold disinfection of instruments and endoscopes
Manufacturers & Suppliers
Laboratoires ANIOS
manufacturer
Pavé du Moulin.59260.LILLE - HELLEMMES.FRANCE.
+33 (0)3 20 67 67 67
http://www.anios.com
Emergency Contacts
INRS
+33(0)1 45 42 59 59
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Move the person away from the place of exposure and take him/her outside.
Remove all contaminated or stained clothing immediately. Do not use them again until they have been decontaminated. Rinse immediately and thoroughly with water.
Symptoms: skin irritation
If applicable, remove contact lenses. Wash thoroughly with soft clean water for 15 minutes, holding the eyelids open.
Symptoms: redness, pain or visual impairment
Rinse out the mouth, do not allow to drink, do not induce vomiting. Calm the person down and transfer immediately to hospital or doctor. Show the label to the doctor.
Immediate Medical Attention
Transfer immediately to hospital or doctor in the event of swallowing. Consult an ophthalmologist if there is any redness, pain or visual impairment. Seek medical advice in the event of skin irritation.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Any extinguishing agents are authorized: foam, sand, carbon dioxide, water, powder.
Firefighter Protection
Use autonomous insulating breathing apparatus and a full protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Consult the safety measures listed under headings 7 and 8.
Contain and control the leaks or spills with non-combustible absorbent materials such as sand, earth, vermiculite, diatomaceous earth in drums for waste disposal. Prevent any material from entering drains or waterways.
Absorb any spilled product with absorbent non-combustible materials, and sweep away or remove with a shovel. Put any waste in drums for disposal. Do not mix with any other waste. Wash the contaminated surface thoroughly with water.
Materials: absorbent non-combustible materials
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Product for external use - do not swallow. Avoid all contact with skin or eyes. Do not hermetically seal the container when the mixture ACTIVATOR/GENERATOR has been performed.
Keep well away from combustible materials and reducing agents (amines), acids, bases, heavy metal compounds (accelerators, siccative agents, metallic salts). Keep away from heat. Recommended storage temperature: from +5°C to +25°C. Please refer to safety data sheets of products ACTIVATOR and GENERATOR for their own storage conditions before use. Keep out of the reach of children
Eye bath and water point nearby.
Prevent access by unauthorised personnel.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure the rooms are well-ventilated.
When handling this product, wear suitable gloves. Butyl or nitrile gloves are recommended. Gloves must be replaced immediately if they show signs of wear and tear.
Make safety goggles with side protection available to the personnel. Avoid all contact with skin or eyes.
In case of insufficient ventilation, with the risk of exceeding the TLVs (Treshold Limit Values)/TWA, wear suitable breathing apparatus. Use Type B1P1 or B2P2 filters.
Personnel shall wear regularly laundered overalls.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The preparation is stable at the handling and storage conditions recommended per § 7 of the safety data sheet
Do not mix with other products.
Brass, copper, bronze, aluminium, iron, titane. Powerful organic and inorganic oxidizing compounds.
At high temperatures, dangerous decomposition products may be produced, such as fumes, carbon dioxide and carbon monoxide, nitrogen oxide.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ANIOXYDE 1000_RECONSTITUE?
The signal word is no signal word.
What is the physical form of ANIOXYDE 1000_RECONSTITUE?
ANIOXYDE 1000_RECONSTITUE is a fluid liquid with yellow to orange. color. It has weak, typical of acetic acid odor.
What is ANIOXYDE 1000_RECONSTITUE used for?
Cold disinfection of instruments and endoscopes
What is the melting point of ANIOXYDE 1000_RECONSTITUE?
The melting point is not specified. and the boiling point is not specified..