Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Plastic Clean & Protect
- Product Code
- 85447
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Surface cleanser, Surface protection
Manufacturers & Suppliers
KENT (United Kingdom) Ltd
manufacturer
Forsyth House, Pitreavie Drive, Pitreavie Business Park, Dunfermline, Fife, KY11 8US
+44 01383 723344 / 0800 136925
Emergency Contacts
Emergency Contact
+44 01383 723344
During normal office hours - Monday - Thursday 8.30am - 5.30pm, Friday 9.00am - 3.00pm
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of the substances listed below with harmless additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| butane, pure EC: 203-448-7 | 106-97-8 | 25 - 50% | Yes |
| Hydrocarbons, C7, n-alkanes isoalkanes, cyclic EC: 927-510-4 | --- | 25 - 50% | Yes |
| Propane liquefied EC: 200-827-9 | 74-98-6 | 5 - 10% | Yes |
| White mineral oil, petroleum EC: 232-455-8 | 8042-47-5 | 5 - 10% | Yes |
| Isobutane EC: 200-857-2 | 75-28-5 | 3% | Yes |
| (R)-p-mentha-1,8-diene EC: 227-813-5 | 5989-27-5 | 3% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and call for doctor for safety reasons. In case of unconsciousness bring patient into stable side position for transport.
Instantly wash with water and soap and rinse thoroughly. If skin irritation continues, consult a doctor.
Rinse opened eye for several minutes under running water.
Rinse out mouth. In case of persistent symptoms consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, extinguishing powder or water haze. Fight larger fires with water haze or alcohol-resistant foam. Use fire fighting measures that suit the environment.
Water with a full water jet.
Formation of toxic gases is possible during heating or in case of fire.
Cool endangered containers with water spray jet.
Firefighter Protection
Do not inhale explosion gases or combustion gases. Wear self-contained breathing apparatus. Wear full protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Put on breathing apparatus. Wear protective equipment. Keep unprotected persons away.
Do not allow to enter drainage system, surface or ground water. Do not allow product to reach sewage system or water bodies.
Send for recovery or disposal in suitable containers.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Open and handle container with care. Ensure good interior ventilation, especially at floor level. (Fumes are heavier than air).
Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50°C, i.e. electric lights. Do not pierce or burn, even after use. Do not spray on flames or red-hot objects.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Wear suitable gloves tested to EN 374. Nitrile rubber, NBR. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: Value for the permeation: Level 6 > 480 minutes. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Safety glasses (EN 166)
Only during spraying without adequate removal by suction. A1 / P1 (EN14387)
Protective work clothing (EN-13034/6)
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications.
No further relevant information available.
No dangerous reactions known
No decomposition if used and stored according to specifications.
Strong oxidising agents, Water / humidity
Formation of toxic gases is possible during heating or in case of fire. Carbon monoxide and carbon dioxide Nitrogen oxides (NOx)
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed of together with household garbage.
Must not be disposed of together with household garbage.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2
- Packing Group
- Void
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Plastic Clean & Protect?
The signal word is danger.
What is the physical form of Plastic Clean & Protect?
Plastic Clean & Protect is a aerosol with colourless color. It has characteristic odor.
What is Plastic Clean & Protect used for?
Surface cleanser, Surface protection
What are the hazard statements for Plastic Clean & Protect?
This substance has 6 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H336: May cause drowsiness or dizziness.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of Plastic Clean & Protect?
The melting point is Not determined and the boiling point is Not applicable, as aerosol.