Ethanol, absolute

Remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms occur.

Symptoms: Difficulty in breathing.

Wash off immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Clean mouth with water and drink afterwards plenty of water.

Symptoms: nausea and vomiting

Water spray, carbon dioxide (CO2), dry chemical, alcohol-resistant foam. Water mist may be used to cool closed containers.

Do not use a solid water stream as it may scatter and spread fire.

Flammable. Risk of ignition. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Containers may explode when heated. Vapors may form explosive mixtures with air.

Should not be released into the environment.

Soak up with inert absorbent material.

Materials: inert absorbent material

Wear personal protective equipment/face protection. Do not get in eyes, on skin, or on clothing. Ensure adequate ventilation. Avoid ingestion and inhalation. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded. Take precautionary measures against static discharges.

Keep containers tightly closed in a dry, cool and well-ventilated place. Keep away from open flames, hot surfaces and sources of ignition. Flammables area. Keep away from heat, sparks and flame.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing and gloves, including the inside, before re-use. Wash hands before breaks and after work.

Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded. Take precautionary measures against static discharges.

Ensure adequate ventilation, especially in confined areas. Use explosion-proof electrical/ventilating/lighting equipment. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Butyl rubber (> 480 minutes, 0.38 mm - 0.56 mm, Level 6, EN374-3), Neoprene (> 480 minutes, 0.45 mm, EN 374), PVC (< 60 minutes, 0.18 mm), Viton (R) (> 480 minutes, 0.7 mm). Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Ensure gloves are suitable for the task: Chemical compatibility, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Remove gloves with care avoiding skin contamination.

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Organic gases and vapours filter Type A Brown conforming to EN14387. Small scale/Laboratory use: Maintain adequate ventilation

Long sleeved clothing.

Prevent product from entering drains. Do not allow material to contaminate ground water system.

Hygroscopic.

None known, based on information available

Hazardous polymerization does not occur. Hazardous Reactions None under normal processing.

Incompatible products. Heat, flames and sparks. Keep away from open flames, hot surfaces and sources of ignition.

Strong oxidizing agents. Strong acids. Acid anhydrides. Acid chlorides.

Carbon monoxide (CO). Carbon dioxide (CO₂).