NextSDS Logo
Safety Data Sheet EN

Compressor Oil 1 L

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Compressor Oil 1 L
Product Code
0901004170

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Lubricant for Industrial use, Compressor lubricant

Uses advised against

No further relevant information available.

Manufacturers & Suppliers

M

Metabowerke GmbH

manufacturer

Metabo-Allee-1 – DE-72622 Nürtingen

0049 / (0) 7022 / 72-0

Emergency Contacts

NHS

+44 (0) 344 892 0111

NHS

111

NHS 24

111

Emergency Contact

01 809 2166

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

Hazard Classifications

Not Classified

GHS Pictograms

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type uvcb

Product based on mineral oil with a DMSO extract <3% (IP 346).

Chemical Name CAS Number Concentration Hazardous
Destillate (Erdöl), mit Wasserstoff behandelte schwere, naphthenhaltige --- --- No

For the wording of the listed hazard phrases refer to section 16.

Notes

Dangerous components: Void

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Supply fresh air; consult doctor in case of complaints.

Skin contact

Immediately wash with water and soap and rinse thoroughly.

Eye contact

Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.

Ingestion

Rinse out mouth and then drink plenty of water. No neutralization attempt. Do not induce vomiting.

Symptoms: Gastric or intestinal disorders

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.

Unsuitable media

Water with full jet

Specific hazards

In case of fire, the following can be released: oxides of carbon, Nitrogen oxides (NOx), Smoke

Instructions

Cool endangered containers with water spray from a safe distance. Do not inhale explosion and combustion gases.

Firefighter Protection

Wear self-contained respiratory protective device.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Particular danger of slipping on leaked/spilled product.

Environmental

Do not allow to penetrate the ground/soil. Do not allow to enter sewers/ surface or ground water.

Cleanup methods

Absorb with liquid-binding material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

The usual precautionary measures when handling chemicals should be observed.

Storage

Store in a cool location. Store in cool, dry conditions in well sealed receptacles. Protect from frost.

Fire prevention

Vapors are heavier than air. Explosive vapor - / air - mixtures may be formed avoid rake at high temperatures.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Hands

Recommendation: Chemical resistant protective gloves (EN 374). Material of gloves: Nitrile rubber, NBR; Chloroprene rubber, CR. Recommended thickness of the material: ≥ 0.4 mm. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: Value for the permeation: Level 6 = >480 min. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. Supplementary note: The specifications are based on own tests, literature data and information of glove manufacturers, or is derived by analogy with similar substances. It should be noted, that the practical usage of a chemical-protective glove can in practice due to many influencing factors (eg temperature) may be considerably shorter than the permeation time determined through testing. Due to the large variety the instructions of the manufacturer must be observed.

Eyes

Use safety glasses according to EN 166 : 2001.

Respiratory

Not necessary if room is well-ventilated. Exceeding the recommended exposure limits: In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device. Respiratory protective device with combination filter (EN143 / EN 149): Typ P2 / FFP2. Respirators and components must be tested and approved under appropriate government standards such as NIOSH. (U.S.) or CEN (EU).

Skin/Body

Impervious protective clothing. Non-slip shoes recommended

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Fluid
Form
Fluid
Flammability
Not applicable.
Appearance
Fluid
Relative Evaporation Rate
---
Dynamic Viscosity
Not determined.
Odor Threshold
Not determined.
Upper Explosive Limit
Not determined.
Boiling Point
Undetermined.
Solubility
---
Density
0.9 g/cm³
Metal Corrosion
---
Bulk Density
---
Melting Point
Undetermined.
Decomposition Temperature
Not determined.
Vapor Pressure
<0.1 hPa
Cloud Point
---
Explosive Limits
---
Vapor Density
---
State Under Standard Conditions
---
Auto Ignition Temperature
Product is not selfigniting.
Solubility In Water
Not miscible or difficult to mix.
Colour Intensity
---
Solubility In Fat
---
Solidification Point
---
Crystallisation Point
---
Lower Explosive Limit
Not determined.
Voc Content
0.00 %
Partition Coefficient
Not determined.
Flash Point
228 °C
Kinematic Viscosity
100 mm²/s
Softening Point
---
Evaporation Rate
---
Physical State Data
liquid
Odor
Characteristic
Relative Density
---
Properties Status
---
Freezing Point
Undetermined.
Molecular Weight
---
Ph
Not determined.
Colour
Yellowish
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

The product is chemically stable under normal ambient conditions (room temperature).

Reactivity

Reacts with strong oxidants and strong reducing agents under severe heat.

Hazardous reactions

No dangerous reactions known.

Avoid

Temperatures above 60 °C can lead to reduced shelf life of the product.

Incompatible

No further relevant information available.

Decomposition

Emergence of flammable gases / vapors on contact with strong oxidizing agent's possible.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Compressor Oil 1 L?

The signal word is no signal word.

What is the physical form of Compressor Oil 1 L?

Compressor Oil 1 L is a fluid appearing as fluid with yellowish color. It has characteristic odor.

What is Compressor Oil 1 L used for?

Lubricant for Industrial use, Compressor lubricant

What is the melting point of Compressor Oil 1 L?

The melting point is Undetermined. and the boiling point is Undetermined..