NextSDS Logo
Safety Data Sheet EN

Finixa wheel spray silver - light & ultrafine 400ml

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Finixa wheel spray silver - light & ultrafine 400ml
Product Code
TSP 520

Regulatory Identifiers

CAS Number
N/A

Identified Uses

SU3 Industrial uses: Uses of substances as such or in preparations at industrial sites, SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen), SU21 Consumer uses: Private households / general public / consumers, PC9a Coatings and paints, thinners, paint removers, PROC7 Industrial spraying, PROC11 Non industrial spraying, Application of the substance / the mixture Paint

Manufacturers & Suppliers

C

Chemicar Europe

distributor

Baarbeek 2, B-2070 Zwijndrecht

+32 (0) 3 234 87 80

Emergency Contacts

Emergency Contact

+(32) (0)3 760 08 09

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Aerosol Cat. 1 H222
Skin Irrit. Cat. 2 H315
Eye Irrit. Cat. 2 H319
STOT SE Cat. 3 H336
Aquatic Chronic Cat. 3 H412

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H222 Extremely flammable aerosol. Pressurised container: May burst if heated.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.

Precautionary Statements

P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Pressurized container: Do not pierce or burn, even after use.
P261 Avoid breathing mist/vapours/spray.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves / eye protection.
P304 + P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P312 Call a POISON CENTER or doctor/physician if you feel unwell
P403 Store in a well-ventilated place.
P410 + P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Acetone EC: 200-662-2 67-64-1 25 - 50% Yes
butane (containing < 0.1% butadiene (203-450-8)) EC: 203-448-7 106-97-8 10 - 25% Yes
propane EC: 200-827-9 74-98-6 10 - 25% Yes
xylene (mix) EC: 215-535-7 1330-20-7 12.5 - 20% Yes
Solvent naphtha (petroleum), light arom. Benzene<0.1% EC: 918-668-5 64742-95-6 0.3 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Supply fresh air; If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist. In case of unconsciousness place patient stably in side position for transportation.

Skin contact

Generally the product does not irritate the skin.

Eye contact

Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.

Ingestion

Do not induce vomiting; call for medical help immediately

Immediate Medical Attention

Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water haze, Fire-extinguishing powder, Carbon dioxide, Alcohol resistant foam

Unsuitable media

Water with full jet

Specific hazards

No further relevant information available.

Firefighter Protection

Mount respiratory protective device.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Wear protective equipment. Keep unprotected persons away.

Environmental

Do not allow product to reach sewage system or any water course. Do not allow to enter sewers/ surface or ground water.

Cleanup methods

Dispose contaminated material as waste according to item 13. Do not flush with water or aqueous cleansing agents.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Open and handle receptacle with care.

Storage

Store in a cool location. Observe official regulations on storing packagings with pressurized containers. Keep receptacle tightly sealed. Do not seal receptacle gas tight. Store in cool, dry conditions in well sealed receptacles. Protect from heat and direct sunlight.

Fire prevention

Keep ignition sources away - Do not smoke. Protect against electrostatic charges.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Hands

Protective gloves Solvent resistant gloves Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation Material of gloves: Nitrile rubber, NBR Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.

Eyes

Tightly sealed goggles

Respiratory

In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device. Use suitable respiratory protective device in case of insufficient ventilation. Filter AX/P2

Skin/Body

Use protective suit.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Aerosol
Physical State Data
aerosol
State Under Standard Conditions
---
Appearance
silver grey
Colour
silver grey
Colour Intensity
---
Form
Aerosol
Odor
Characteristic
Odor Threshold
Not determined.
Ph
Not determined.
Melting Point
Undetermined.
Boiling Point
-44 °C
Flash Point
-97 °C
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not applicable
Vapor Pressure
4 Bar
Vapor Density
Not determined
Relative Density
Not determined
Bulk Density
---
Density
0.704 g/cm³
Flammability
Not applicable
Upper Explosive Limit
13.0 Vol %
Lower Explosive Limit
1.1 Vol %
Explosive Limits
---
Auto Ignition Temperature
365 °C
Decomposition Temperature
Not determined.
Solubility
---
Partition Coefficient
Not determined.
Solubility In Water
Not miscible or difficult to mix
Solubility In Fat
---
Molecular Weight
---
Voc Content
---
Metal Corrosion
---
Dynamic Viscosity
Not determined
Kinematic Viscosity
Not determined
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if used according to specifications.

Hazardous reactions

No dangerous reactions known

Avoid

No further relevant information available

Incompatible

No further relevant information available.

Decomposition

No dangerous decomposition products known.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1950
Shipping Name
AEROSOLS
Transport Class
2.1
ADR

Warning: Gases.

IMDG

Warning: Gases.

IATA

Warning: Gases.

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Finixa wheel spray silver - light & ultrafine 400ml?

The signal word is danger.

What is the physical form of Finixa wheel spray silver - light & ultrafine 400ml?

Finixa wheel spray silver - light & ultrafine 400ml is a aerosol appearing as silver grey with silver grey color. It has characteristic odor.

What is Finixa wheel spray silver - light & ultrafine 400ml used for?

SU3 Industrial uses: Uses of substances as such or in preparations at industrial sites, SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen), SU21 Consumer uses: Private households / general public / consumers, PC9a Coatings and paints, thinners, paint removers, PROC7 Industrial spraying, PROC11 Non industrial spraying, Application of the substance / the mixture Paint

What are the hazard statements for Finixa wheel spray silver - light & ultrafine 400ml?

This substance has 4 hazard statements:

  • H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
  • H315: Causes skin irritation.
  • H319: Causes serious eye irritation.
  • H336: May cause drowsiness or dizziness.

What is the melting point of Finixa wheel spray silver - light & ultrafine 400ml?

The melting point is Undetermined. and the boiling point is -44 °C.