Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- TotalSource Synthetic heavy-duty metallic coating
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Paint
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
TVH Parts NV
manufacturer
Brabantstraat 15, 8790 Waregem, Belgium
+32 56 43 64 36
http://www.tvh.com
Emergency Contacts
Emergency Contact
+32 56 43 64 36
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, < 2% aromatics EC: 919-857-5 | --- | 10 - 25% | Yes |
| Xylene EC: 215-535-7 | 1330-20-7 | 5 - 10% | Yes |
| 2-Methoxy-1-methylethyl acetate EC: 203-603-9 | 108-65-6 | 2.5 - 10% | Yes |
| 1-methoxy-2-propanol EC: 203-539-1 | 107-98-2 | 2.5 - 10% | Yes |
| Ethylbenzene EC: 202-849-4 | 100-41-4 | 2.5% | Yes |
| n-Butyl acetate EC: 204-658-1 | 123-86-4 | 1 - 2.5% | Yes |
| 2-Butoxyethyl acetate EC: 203-933-3 | 112-07-2 | 1 - 2.5% | Yes |
| barium bis(2-ethylhexanoate) EC: 219-535-8 | 2457-01-4 | 1% | Yes |
| Cobalt bis(2-ethylhexanoate) EC: 205-250-6 | 136-52-7 | 0.1 - 0.25% | Yes |
| 2-ethylhexanoic acid, zirconium salt EC: 245-018-1 | 22464-99-9 | 1% | Yes |
| Hexanoic acid, 2-ethyl-, zinc salt, basic EC: 286-272-3 | 85203-81-2 | 1% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately rinse with water.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
Firefighter Protection
No special measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
TotalSource Acrylic fast dry high coverage coating spray
---
TOTAL SOURCE PAINT
---
Construction Top Coat
---
2100 Hard-Hat Series Topcoat
UFI: K741-N0HT-0009-1809
2100 Hard-Hat Series Topcoat
UFI: K741-N0HT-0009-1809
TOP COAT SILVER
---
BONDERITE M-NT 1455T CONVERSION COATING
---
BONDERITE M-NT 41042 CONVERSION COATING
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Keep container tightly sealed.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Protective gloves (EN 374). The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Breakthrough time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
Carbon monoxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1263
- Shipping Name
- PAINT
- Transport Class
- 3
- Packing Group
- III
Warning: Flammable liquids.
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for TotalSource Synthetic heavy-duty metallic coating?
The signal word is warning.
What is the physical form of TotalSource Synthetic heavy-duty metallic coating?
TotalSource Synthetic heavy-duty metallic coating is a fluid with according to product specification color. It has characteristic odor.
What is TotalSource Synthetic heavy-duty metallic coating used for?
Paint
What are the hazard statements for TotalSource Synthetic heavy-duty metallic coating?
This substance has 3 hazard statements:
- H226: Flammable liquid and vapour.
- H317: May cause an allergic skin reaction.
- H336: May cause drowsiness or dizziness.
What is the melting point of TotalSource Synthetic heavy-duty metallic coating?
The melting point is Undetermined. and the boiling point is 137-143 °C (1330-20-7 Xylene).