Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Fatty acids, tall-oil, compounds with triethanola | 68132-46-7 | 5 - 10% | Yes |
| Tall oil fatty acids, ethoxylated | 61791-00-2 | 1 - 5% | Yes |
| Oleyl alcohol, ethoxylated, phosphated, triethanolamine salt | 68051-99-0 | 1 - 5% | Yes |
| Potassium soap of tall oil fatty acids | 61790-44-1 | 1 - 5% | Yes |
| Tris(2-hydroxyethyl)hexahydro triazine | 4719-04-4 | 1 - 5% | Yes |
Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove person immediately to fresh air.
Flush with large amounts of water.
Rinse immediately with plenty of water.
Do not induce vomiting.
Immediate Medical Attention
Seek medical attention if symptoms develop or persist (inhalation, skin contact). Seek medical advice (eye contact). Get immediate medical attention (ingestion).
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Materials: inert material
Related Products
Similar products with comparable safety profiles
BONDERITE L-FM F 721 STAMPING LUBRICANT ACHESON known as MULTAN F 721
---
BONDERITE L-FM MP-404 STAMPING LUBRICANT ACHESON known as MULTAN PL PREL UBE MP-404
---
BONDERITE L-FM F 738 FORMING LUBRICANT ACHESON known as MULTAN F 738
---
BONDERITE L-FM 12MA STAMPING LUBRICANT ACHESON known as LUBE 12-MA
---
BONDERITE L-FM F P 1212 AN STAMPING LUBRICANT
---
BONDERITE L-MR 8304 MACHINING LUBRICANT known as MULTAN 8304
---
BONDERITE L-FM PL-A POST LUBRICANT ACHESON
---
BONDERITE L-FM 8100-A POST LUBRICANT ACHESON
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Avoid breathing vapors or mists of this product. Provide adequate ventilation. Wash thoroughly after handling. Do not take internally.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide local and general exhaust ventilation to effectively remove and prevent buildup of any vapors or mists generated from the handling of this product.
Chemical resistant, impermeable gloves. Gloves should be tested to determine suitability for prolonged contact.
Wear safety glasses; chemical goggles (if splashing is possible).
If ventilation is not sufficient to effectively prevent buildup of aerosols, mists or vapors, appropriate NIOSH/MSHA respiratory protection must be provided.
Use of impervious apron and boots are recommended.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Stable under normal conditions of storage and use.
Strong oxidizing agents.
Upon decomposition, this product may yield gaseous nitrogen oxides, carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750?
The signal word is danger.
What is the physical form of BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750?
BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750 is a liquid with brown color. It has mild surfactant odor.
What is the solubility of BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750?
Complete Water
What is BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750 used for?
Lubricant
What are the hazard statements for BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750?
This substance has 3 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
- H318: CAUSES SERIOUS EYE DAMAGE.
What is the melting point of BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750?
The melting point is Not determined and the boiling point is >100 °C (>212°F) None.