Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Notes
Hazardous Component(s): None
First Aid Measures
Emergency procedures for chemical exposure incidents
If mist or vapor of this product is inhaled, remove person immediately to fresh air. Seek medical attention if symptoms develop or persist.
Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention.
In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention.
Get medical attention. DO NOT induce vomiting unless directed to do so by medical personnel.
Immediate Medical Attention
Seek medical attention if symptoms develop or persist (inhalation/skin). Seek immediate medical attention (eye). Get medical attention (ingestion).
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so. Do not allow product to enter sewer or waterways.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Materials: inert material
Related Products
Similar products with comparable safety profiles
BONDERITE L-FM PL 633 STAMPING LUBRICANT ACHESON known as MULTAN PL 633
---
BONDERITE L-FM PL 298 STAMPING LUBRICANT ACHESON known as MULTAN PL 298
---
BONDERITE L-FM MP-404 STAMPING LUBRICANT ACHESON known as MULTAN PL PRELUBE MP-404
---
BONDERITE L-FM F 721 STAMPING LUBRICANT ACHESON known as MULTAN F 721
---
BONDERITE L-FM MP-404 STAMPING LUBRICANT ACHESON known as MULTAN PL PREL UBE MP-404
---
BONDERITE L-FM F 750 STAMPING LUBRICANT ACHESON known as MULTAN F 750
---
BONDERITE L-FM F B27MC6A STAMPING LUBRICANT ACHESON known as MULTAN F B2 7MC6A 9
---
BONDERITE L-FM F 747 STAMPING LUBRICANT ACHESON known as MULTAN F 747
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Use only with adequate ventilation. Avoid breathing mists or aerosols of this product. Do not take internally. For industrial use only.
Not available.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide local and general exhaust ventilation to effectively remove and prevent buildup of any vapors or mists generated from the handling of this product.
Wear impervious gloves for prolonged contact. Gloves should be tested to determine suitability for prolonged contact.
Wear safety glasses; chemical goggles (if splashing is possible).
If ventilation is not sufficient to effectively prevent buildup of aerosols, mists or vapors, appropriate NIOSH/MSHA respiratory protection must be provided.
Use of impervious apron and boots are recommended.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Keep away from heat, ignition sources and incompatible materials.
Strong acids and strong bases.
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453?
The signal word is no signal word.
What is the physical form of BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453?
BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453 is a liquid with amber color. It has mild odor.
What is the solubility of BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453?
Negligible
What is BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453 used for?
Lubricant
What is the melting point of BONDERITE L-FM PL 1453 ACHESON STAMPING LUBRICANT known as MULTAN PL 1453?
The melting point is Not determined and the boiling point is 250 °C (482°F)calculated.