NextSDS Logo
Safety Data Sheet EN

LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL
Product Code
EB4412-B50

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Part B of 2-Component Epoxy Adhesive.

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Corr. Cat. 1
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Carc. Cat. 1A
Repr. Cat. 2

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS08 - Serious health hazard

GHS08

Hazard Statements

H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H350 MAY CAUSE CANCER.
H361 SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Fatty acids, tall-oil, reaction products with tetraethylenepentamine 68953-36-6 30 - 60% Yes
Tetraethylene pentamine 112-57-2 5 - 10% Yes
Bisphenol A, epichlorohydrin polymer, diethylenetriamine adduct 68610-56-0 1 - 5% Yes
4,4'-Isopropylidenediphenol 80-05-7 1 - 5% Yes
Diethylenetriamine 111-40-0 1 - 5% Yes
Limestone 1317-65-3 1 - 5% Yes
Strontium oxide 1314-11-0 0.1 - 1% Yes
Quartz (SiO2) 14808-60-7 0.1 - 1% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air.

Skin contact

Rinse with running water and soap. Remove contaminated clothing and shoes. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.

Ingestion

Do not induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Seek medical attention immediately for eye contact. Seek immediate medical attention for ingestion. If symptoms persist, seek medical advice.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Ensure adequate ventilation. Remove all sources of ignition. Keep unnecessary personnel away. Wear appropriate personal protective equipment. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wear suitable protective clothing, safety glasses and gloves. Keep container closed.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in a dry place.

Hygiene

Wash thoroughly after handling. When using do not eat, drink or smoke.

Fire prevention

Remove all sources of ignition. Keep away from heat, spark and flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Upper Explosive Limit
Not available.
Colour
White
Boiling Point
Not available.
Physical State Data
liquid
Freezing Point
---
Form
---
Vapor Pressure
< 1.0 mm hg
Cloud Point
---
Bulk Density
---
Properties Status
---
Colour Intensity
---
Odor
Ammoniacal
Solidification Point
---
Crystallisation Point
---
Melting Point
Not available.
Metal Corrosion
---
Physical State
Liquid
Decomposition Temperature
Not available.
Vapor Density
---
Density
---
Solubility In Water
---
Flammability
Not applicable
Dynamic Viscosity
Not available.
State Under Standard Conditions
---
Solubility
Partially miscible Water
Molecular Weight
---
Flash Point
195 °C (383°F) Closed cup
Solubility In Fat
---
Softening Point
---
Partition Coefficient
Not available.
Evaporation Rate
Not available.
Auto Ignition Temperature
Not determined
Relative Evaporation Rate
---
Odor Threshold
Not available.
Ph
Alkaline
Appearance
---
Kinematic Viscosity
Not available.
Lower Explosive Limit
Not available.
Relative Density
1.4
Explosive Limits
---
Voc Content
< 1 %; < 10 g/l (estimated value for resin and hardener mixed together)
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Protect from direct sunlight.

Incompatible

Oxidizing agents. Acids. Bases. Amines.

Decomposition

Oxides of carbon. Phenolics. Toxic fumes. Irritating vapors.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN2735
Shipping Name
Amines, liquid, corrosive, n.o.s. (Tetraethylene pentamine, Diethylenetriamine)
Transport Class
8
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL?

The signal word is danger.

What is the physical form of LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL?

LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL is a liquid with white color. It has ammoniacal odor.

What is the solubility of LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL?

Partially miscible Water

What is LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL used for?

Part B of 2-Component Epoxy Adhesive.

What are the hazard statements for LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL?

This substance has 5 hazard statements:

  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H350: MAY CAUSE CANCER.
  • H361: SUSPECTED OF DAMAGING FERTILITY OR THE UNBORN CHILD.

What is the melting point of LOCTITE STYCAST ES 4412 PTB known as HYSOL ES4412 PART B GAL?

The melting point is Not available. and the boiling point is Not available..