Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE M-NT 1800 MU A CONVERSION COATING
- Product Code
- 1247386
- Synonyms
- TECTALIS 1800 MAKEUP A
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Conversion coating
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
CHEMTREC
1-703-527-3887
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hexafluorozirconic acid | 12021-95-3 | 1 - 5% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
If mist or vapor of this product is inhaled, remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. If breathing is difficult, give oxygen. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes.
Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. GET IMMEDIATE MEDICAL ATTENTION. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided.
Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.
Get immediate medical attention. Do not induce vomiting. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to a victim who is unconscious or is having convulsions.
Immediate Medical Attention
Get immediate medical attention.
Medical Treatment
Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use media appropriate for surrounding material.
Not available.
This product is an aqueous mixture which will not burn. May react with metals to form flammable hydrogen gas.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways.
Absorb spill with inert material. Shovel material into appropriate container for disposal. Dispose of according to Federal, State and local governmental regulations.
Materials: inert material
Related Products
Similar products with comparable safety profiles
BONDERITE M-NT 1800 MU A CONVERSION COATING
---
BONDERITE M-NT 1455T CONVERSION COATING
---
BONDERITE M-NT 8453 CONVERSION COATING
---
BONDERITE M-NT 41042 CONVERSION COATING
---
BONDERITE M-NT 770X R N CONVERSION COATING
---
BONDERITE M-NT 404 CONVERSION COATING
---
BONDERITE M-NT 404 CONVERSION COATING
---
BONDERITE M-NT 1200 R20 CONVERSION COATING
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Do not inhale vapors and fumes. Wash thoroughly after handling. Do not take internally. For industrial use only.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Do not freeze.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Store away from incompatible materials.
Avoid contact with organic materials, oils, greases, and any oxidizable materials. This material will react with glass, concrete, certain metals, silica containing materials, rubber, leather, and many organics. This product may react with strong alkalies.
May liberate hydrogen fluoride. Decomposes with heat to produce oxides of nitrogen.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What other names is BONDERITE M-NT 1800 MU A CONVERSION COATING known by?
BONDERITE M-NT 1800 MU A CONVERSION COATING is also known as: TECTALIS 1800 MAKEUP A
What is the hazard signal word for BONDERITE M-NT 1800 MU A CONVERSION COATING?
The signal word is warning.
What is the physical form of BONDERITE M-NT 1800 MU A CONVERSION COATING?
BONDERITE M-NT 1800 MU A CONVERSION COATING is a liquid with clear color. It has odourless / odorless odor.
What is the solubility of BONDERITE M-NT 1800 MU A CONVERSION COATING?
Complete
What is BONDERITE M-NT 1800 MU A CONVERSION COATING used for?
Conversion coating
What are the hazard statements for BONDERITE M-NT 1800 MU A CONVERSION COATING?
This substance has 2 hazard statements:
- H315: CAUSES SKIN IRRITATION
- H319: CAUSES SERIOUS EYE IRRITATION
What is the melting point of BONDERITE M-NT 1800 MU A CONVERSION COATING?
The melting point is Not determined and the boiling point is > 100 °C (> 212°F).