NextSDS Logo
Safety Data Sheet EN

BONDERITE M-NT 404 CONVERSION COATING

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-NT 404 CONVERSION COATING
Product Code
2587091

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Conversion coating

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4
Acute Tox. Cat. 3
Skin Corr. Cat. 1
Eye Dam. Cat. 1

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

Hazard Statements

H302 HARMFUL IF SWALLOWED.
H311 TOXIC IN CONTACT WITH SKIN.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.

Precautionary Statements

P260 Do not breathe vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P361 + P364 Take off immediately all contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Hexafluorozirconic acid 12021-95-3 1 - 5% Yes
Ammonium nitrate 6484-52-2 1 - 5% Yes
Hydrogen fluoride 7664-39-3 0.1 - 1% Yes
Nitric acid 7697-37-2 0.1 - 1% Yes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If mist or vapor of this product is inhaled, remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. If breathing is difficult, give oxygen. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes.

Skin contact

Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided.

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Eye flushing should continue during transportation to a doctor.

Ingestion

DO NOT induce vomiting unless directed to do so by medical personnel. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to a victim who is unconscious or is having convulsions.

Immediate Medical Attention

GET IMMEDIATE MEDICAL ATTENTION (for skin contact, eye contact, and ingestion).

Medical Treatment

Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use media appropriate for surrounding material.

Unsuitable media

Not available.

Specific hazards

This product is an aqueous mixture which will not burn.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Wear appropriate personal protective equipment. Do not allow product to enter sewer or waterways.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal.

Materials: inert material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Do not breathe fumes or dust from this material. Wash thoroughly after handling. Use caution when combining with water; DO NOT add water to acid, ALWAYS add acid to water while stirring to prevent release of heat, steam and fumes.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Thaw and mix thoroughly if frozen.

Hygiene

Wash thoroughly after handling.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Freezing Point
---
Flash Point
Not applicable
Upper Explosive Limit
Not available.
Form
---
Melting Point
Not determined
Bulk Density
---
Physical State
Liquid
Odor
Acidic
Evaporation Rate
Not available.
Solubility In Fat
---
Auto Ignition Temperature
Not applicable
Metal Corrosion
---
Crystallisation Point
---
Density
---
Molecular Weight
---
Physical State Data
liquid
Voc Content
Not applicable
Cloud Point
---
State Under Standard Conditions
---
Solubility In Water
---
Softening Point
---
Dynamic Viscosity
Not available.
Flammability
Not applicable
Properties Status
---
Solidification Point
---
Relative Evaporation Rate
---
Odor Threshold
Not available.
Decomposition Temperature
Not available.
Explosive Limits
---
Vapor Pressure
Not determined
Colour Intensity
---
Kinematic Viscosity
Not available.
Colour
Colourless / Colorless
Boiling Point
> 100 °C (> 212°F) calculated
Appearance
---
Ph
< 1.5
Solubility
Complete Water
Lower Explosive Limit
Not available.
Relative Density
1.02 - 1.05
Partition Coefficient
Not determined
Vapor Density
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable at normal conditions.

Reactivity

Not available.

Hazardous reactions

Will not occur.

Avoid

None identified.

Incompatible

Avoid contact with organic materials, oils, greases, and any oxidizable materials. This material will react with glass, concrete, certain metals, silica containing materials, rubber, leather, and many organics. This product may react with strong alkalies.

Decomposition

May liberate hydrogen fluoride. Decomposes with heat to produce oxides of nitrogen.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
3264
Shipping Name
Corrosive liquid, acidic, inorganic, n.o.s. (Fluorozirconic acid, Hydrofluoric acid)
Transport Class
8
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE M-NT 404 CONVERSION COATING?

The signal word is danger.

What is the physical form of BONDERITE M-NT 404 CONVERSION COATING?

BONDERITE M-NT 404 CONVERSION COATING is a liquid with colourless / colorless color. It has acidic odor.

What is the solubility of BONDERITE M-NT 404 CONVERSION COATING?

Complete Water

What is BONDERITE M-NT 404 CONVERSION COATING used for?

Conversion coating

What are the hazard statements for BONDERITE M-NT 404 CONVERSION COATING?

This substance has 3 hazard statements:

  • H302: HARMFUL IF SWALLOWED.
  • H311: TOXIC IN CONTACT WITH SKIN.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.

What is the melting point of BONDERITE M-NT 404 CONVERSION COATING?

The melting point is Not determined and the boiling point is > 100 °C (> 212°F) calculated.