NextSDS Logo
Safety Data Sheet EN

LOCTITE E-120HP 20KG Harden M/L

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE E-120HP 20KG Harden M/L
Product Code
1403936

Regulatory Identifiers

CAS Number
N/A

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Corr. Cat. 1C H314
Eye Dam. Cat. 1 H314
Skin Sens. Cat. 1 H317

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

Hazard Statements

H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.

Precautionary Statements

P261 Avoid breathing mist/vapours.
P264 Wash affected area thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P362 + P364 Take off contaminated clothing and wash it before reuse.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Fatty acids, C18-unsatd., dimers, oligomeric reaction products with fatty acids, C16-18 and C18-unsatd., branched and linear and tri 157707-72-7 60 - 80% Yes
Amines, polyethylenepoly-, tetraethylenepentamine fraction 90640-66-7 10 - 30% Yes
Amines, polyethylenepoly-, triethylenetetramine fraction 90640-67-8 5 - 10% Yes
3,6,9,12-tetraazatetradecamethylenediamine 4067-16-7 0.1 - 1% Yes

Notes

* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. Get medical attention.

Skin contact

Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and footwear. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.

Eye contact

Immediately flush eyes with plenty of water for at least 15 minutes. Get immediate medical attention.

Ingestion

DO NOT induce vomiting unless directed to do so by medical personnel. Rinse the mouth. Drink 1-2 glasses of water. Never give anything by mouth to an unconscious person. Get immediate medical attention.

Immediate Medical Attention

Get immediate medical attention.

Medical Treatment

Treat symptomatically and supportively.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Dry chemical. Carbon dioxide. Alcohol foam.

Unsuitable media

Not available.

Specific hazards

Personnel in vicinity and downwind should be evacuated. Burning produces obnoxious and toxic fumes. In case of fire, keep containers cool with water spray. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Cartridge respirators do not provide adequate protection for fire fighters or exotherm mitigation.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Cartridge respirators do not provide adequate protection for fire fighters or exotherm mitigation.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Do not allow product to enter sewer or waterways.

Cleanup methods

Ensure adequate ventilation. Wear appropriate personal protective equipment. Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Scrape up spilled material and place in a closed container for disposal.

Materials: inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Use only with adequate ventilation. Keep container closed.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Keep away from heat, spark and flame. Protect from direct sunlight. Avoid moisture.

Hygiene

Wash thoroughly after handling.

Fire prevention

Keep away from heat, spark and flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Use local ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits.

Hands

gloves

Eyes

Safety goggles or safety glasses with side shields. Full face protection should be used if the potential for splashing or spraying of product exists.

Respiratory

Use NIOSH approved respirator if there is potential to exceed exposure limit(s).

Skin/Body

chemical resistant, impermeable clothing and either an apron or body suit to prevent skin contact.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State Data
liquid
Voc Content
< 1.0 %; < 10 g/l Estimated
Flash Point
> 93 °C (> 199.4 °F); Estimated
Solubility In Water
---
Cloud Point
---
Decomposition Temperature
Not available.
Relative Evaporation Rate
---
Solubility In Fat
---
Odor
Mild
Kinematic Viscosity
> 20.5 mm2/s
Physical State
Liquid
Relative Density
0.9 - 1.1
Colour
Amber
Appearance
---
Colour Intensity
---
Explosive Limits
---
Dynamic Viscosity
Not available.
Solubility
Partially miscible Water
Properties Status
---
Flammability
The product is not flammable.
Vapor Density
---
Upper Explosive Limit
Not available.
Solidification Point
---
Molecular Weight
---
Freezing Point
---
Boiling Point
> 93 °C (> 199.4 °F) 1,013 hPa
Lower Explosive Limit
Not available.
Bulk Density
---
Partition Coefficient
Not available.
Melting Point
Not applicable, Product is a liquid
Ph
Product is non-soluble (in water), Not applicable
Density
---
Form
---
Auto Ignition Temperature
Not available.
Crystallisation Point
---
Odor Threshold
Not available.
Softening Point
---
Metal Corrosion
---
Evaporation Rate
Not available.
Vapor Pressure
< 700 mbar (20 °C (68°F))
State Under Standard Conditions
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Exposure to water vapour. Exposure to sunlight.

Incompatible

Strong oxidizing agents. Acids. Organic acids. Mineral acids. Sodium hypochlorite. This product slowly corrodes copper, aluminum, zinc and galvanized surfaces. Reaction with peroxides may result in violent decomposition of peroxide possibly creating an explosion. Bases.

Decomposition

Ammonia. Oxides of carbon. Oxides of nitrogen. Aldehydes. Ketones. Nitric acid.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
2735
Shipping Name
Amines, liquid, corrosive, n.o.s.
Transport Class
8
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE E-120HP 20KG Harden M/L?

The signal word is danger.

What is the physical form of LOCTITE E-120HP 20KG Harden M/L?

LOCTITE E-120HP 20KG Harden M/L is a liquid with amber color. It has mild odor.

What is the solubility of LOCTITE E-120HP 20KG Harden M/L?

Partially miscible Water

What are the hazard statements for LOCTITE E-120HP 20KG Harden M/L?

This substance has 2 hazard statements:

  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.

What is the melting point of LOCTITE E-120HP 20KG Harden M/L?

The melting point is Not applicable, Product is a liquid and the boiling point is > 93 °C (> 199.4 °F) 1,013 hPa.